LABORIE Nexam Pro CIM Скачать руководство пользователя

Страница: 71 / 278

Urodynamic Catheters & Transducers Nexam Pro User Manual

3.6.5

Flushing and Zeroing Water Catheters

Water catheters and DT-XX pressure transducers need to be flushed and
zeroed before starting the investigation.

Figure 3.17

Flush and zero with syringe

The procedure is as follows:

▪

Catheters and transducers have been prepared as described in the

previous subparagraphs; the transducer holder is at symphysis pubis level.

▪

Connect the syringes filled with sterile water to the pressure transducers as

displayed in Figure 3.17 (optionally, the LABORIE flush set can be used).

▪

Push the blue flushing devices and flush the pressure transducers and

catheter lumens to expel all air bubbles.

▪

Release the flushing devices to stop flushing.

▪

Inspect the pressure transducers, catheter lumens and flow-reducer

visually for air bubbles. If necessary, you will need to flush them again.

▪

Turn all stopcock handles counterclockwise, the text

“OFF” pointed to the

catheter side.

▪

Press the

Zero

all

button to zero-balance all pressures to atmospheric

pressure.

Содержание Nexam Pro CIM























































































































































































































































































Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды

LABORIE Nexam Pro CIM, Руководство пользователя

Результаты поиска

Содержание Nexam Pro CIM

Отзывы:

Похожие инструкции для Nexam Pro CIM

Бренды по названию

Популярные бренды