Korg NAUTILUS Series, Руководство по параметрам, Страница: 519 / 961

SEQUENCER > IFX 8–2: MIDI Routing2
509
8–2: MIDI Routing2
Here you can specify the program oscillator output bus,
effect control bus, and REC bus for each MIDI track 1
through 16.
8–2a: MIDI Routing2
Track 01 (Track Number)
Bus Select (IFX/Indiv. Out Assign) Dkit [Off, On]
You can select this only if the specified program is a drum
program (
Oscillator Mode Drums). These settings can also
be made in the Insert Effect-Routing1. For more
information, please see “Bus Select (IFX/Indiv. Out Assign)
Dkit” on page 507.
Bus Select (IFX/Indiv. Out Assign)
[L/R, IFX1…12, 1…4, 1/2…3/4, Off]
For each track, these parameters specify the bus to which the
program oscillator(s) will be sent. The current settings can
also be viewed in the Routing Map. This parameter can also
be edited from the IFX– MIDI Routing1 page. For more
information, please see “Bus Select (IFX/Indiv.Out Assign)”
on page 507.
FX Control Bus [Off, 1, 2]
Sends the output of the track to an FX Control bus (two-
channel stereo FX Ctrl 1 or 2).
Use the FX Control buses when you want a separate sound
to control the audio input of an effect. You can use two FX
Control buses (each is a two-channel stereo bus) to control
effects in various ways.
For more information, please see “FX Control Buses” on
page 733.
REC Bus (All OSCs to) [Off, 1, 2, 3, 4, 1/2, 3/4]
These settings send the output of the track to the REC buses
(four mono channels: 1, 2, 3, 4).
The REC buses are dedicated internal buses for recording,
used for sampling in the various modes or for recording
audio tracks in SEQUENCER mode. In SEQUENCER
mode, you can use these buses to record audio tracks onto
the drive, or to sample.
You will normally use audio track recording to record
external audio signals such as guitar or vocal that are input
from the Audio Input jacks, but you can also record the
playback of MIDI tracks or your performance using the
keyboard or Arpeggiator function. Use
REC Bus to send the
desired tracks to the REC buses, and select REC1–4 (REC
1/2, 3/4) as the
REC Source (0–2a) so that the signals sent
to the REC buses can be recorded.
You can also resample (mix-down) the song playback onto
the drive to create a stereo WAVE file, or sample external
audio sources from the Audio Inputs into RAM (the In-Track
Sampling function). Use the
REC Bus setting to send the
desired tracks or audio inputs to the REC buses for sampling
or resampling, and set
Source Bus (Home– Sampling -
Sampling Setup) to REC1/2 or 3/4 so that these signals can
be sampled.
Off: The signal will not be sent to a REC bus. Normally you
will leave this off.
1, 2, 3, 4: The output of the track will be sent to the
corresponding REC bus. The Pan setting (0–1b) of each
track will be ignored, and the signal will be sent in monaural.
1/2, 3/4: The output of the track will be sent in stereo to the
corresponding pair of REC buses. The signal is sent in stereo
to REC buses 1/2 or 3/4 according to the
Pan setting (0–1b)
of each track.
Track 02…16 (Track Number)
These settings specify the program oscillator output bus,
effect control bus, and REC bus used by MIDI tracks 2
through 16. These are the same as for track 1. See “Track
01”:.
8–1a
8–2PMC
8–2a
1–1a
1–1b