Honda NSS250A Reflex 2001-2007 Скачать руководство пользователя страница 595 | Manualshive

Страница: 595 / 718

background image

LIGHTS/METERS/SWITCHES

22-25

NEEDLE MOVES BUT IT MOVES ABNORMAL

Remove the ECT sensor (page 6-92).

Suspend the ECT sensor in a pan of coolant (1:1
mixture) on an electric heating element and mea-
sure the resistance between the ECT sensor termi-
nal and body as the coolant heats up.

• Soak the ECT sensor in coolant up to its threads

with at least 40 mm (1.57 in) from the bottom of
the pan to the bottom of the sensor.

• Keep the temperature constant for 3 minutes

before testing. A sudden change of temperature
will result in incorrect reading. Do not let the
thermometer or ECT sensor touch the pan.

Connect the tester probe to the sensor terminal is
shown in the illustration.

If the resistance is out of above range by 10% at any
temperature listed, replace the ECT sensor.

Install the ECT sensor (page 6-92).

EOP SWITCH

INSPECTION

Before checking the EOP switch, check the engine
oil level (page 4-10).

Turn the ignition switch ON, engine stop switch " "
and check the oil pressure indicator.

If the indicator does not come on or the indicator
stays on, check the EOP switch and related circuit as
follows:

Uncover the dust cover.

Remove the terminal screw and wire terminal from
the EOP switch.

Contact the wire terminal to the ground.

Turn the ignition switch ON, engine stop switch " "
and check the oil pressure indicator.

• If the indicator comes on, check the oil pressure

(page 5-5). If the oil pressure is proper, replace
the EOP switch.

• If the indicator does not come on, check for an

open circuit in the Blue/red wire. If the wire is
properly, replace the combination meter circuit
board.

Keep all flammable

materials away

from the electric

heating element.

Wear protective

clothing, insulated

gloves and eye

protection.

CONNECTION: Green/blue – Ground

STANDARD:
Temperature

50

°

C (122

°

F)

80

°

C (176

°

F)

Resistance

6.8 – 7.4 k

Ω

2.1 – 2.7 k

Ω

ECT SENSOR

Green/blue (METER SIGNAL)

OIL PRESSURE INDICATOR

SCREW

DUST COVER

WIRE TERMINAL

maxiscooter-club.ru

«
...
593
594
595
596
597
...
»

Содержание NSS250A Reflex 2001-2007















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NSS250A Reflex 2001-2007

Бренд: KEDO Страницы: 2

Бренд: KEDO Страницы: 3

Бренд: KEDO Страницы: 2

Бренд: Yamaha Страницы: 94

Бренд: R&G Страницы: 13

Бренд: KEEWAY Страницы: 15

Бренд: GYS Страницы: 36

Бренд: AGV Страницы: 45

Бренд: Clas Ohlson Страницы: 5

Бренд: BMW Страницы: 139

Бренд: Yamaha Страницы: 119

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 360

Бренд: Yamaha Страницы: 580

Бренд: Yamaha Страницы: 98

Бренд: DYNATEK Страницы: 12

Бренд: Barton Страницы: 35

Бренд: Fuelpak Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды