Honda NSS250A Reflex 2001-2007 Скачать руководство пользователя страница 518 | Manualshive

Страница: 518 / 718

background image

ABS (NSS250A)

18-18

PROBLEM CODE 13, 14, 23 or 43 (Rear
Wheel Speed Sensor/Rear Pulser
Ring/Rear Wheel Lock)

• The ABS indicator might blink under unusual

riding or conditions (page 18-10). This is intermit-
tent failure. Erase the problem code (page 18-9)
then test ride the scooter above 30 km/h (18
mph) and check the problem code by retrieving
the self-diagnosis system (page 18-8).

• If the problem code 43 is indicated, check the

rear brake for drag.

1. Rear Wheel Speed Sensor Air Gap Inspection

Support the scooter on its center stand and raise
the wheel off the ground.
Measure the clearance (air gap) between the
sensor and pulser ring at several points by turn-
ing the wheel slowly.

Is the air gap correct?

YES

–

NO

–

Check each part for deformation and
looseness and correct accordingly.
Recheck the air gap.

2. Rear Wheel Speed Sensor Condition Inspection

Inspect the area around the rear wheel speed
sensor and pulser ring:
Check that there is iron or other magnetic depos-
its between the pulser ring slots and rear wheel
speed sensor, and the pulser ring slots for
obstructions.
Check installation condition of the pulser ring or
rear wheel speed sensor for looseness.
Check the pulser ring and sensor tip for defor-
mation or damage (e.g., chipped pulser ring
teeth).

Are the sensor and pulser ring in good condi-
tion?

YES

–

NO

–

Remove any deposits. Install properly
or replace faulty part.

3. Rear Wheel Speed Sensor Input Voltage

Inspection

Turn the ignition switch OFF.
Disconnect the rear wheel speed sensor 2P
(Orange) connector (page 18-26).

Turn the ignition switch ON.
Measure the voltage at the rear wheel speed
sensor 2P connector of the wire side.

Is there battery voltage?

YES

–

Faulty rear wheel speed sensor

NO

–

STANDARD: 0.2 – 1.2 mm (0.01 – 0.05 in)

0.2 – 1.2 mm (0.01 – 0.05 in)

PULSER RING

REAR WHEEL SPEED SENSOR

CONNECTION: Pink/white (+) – Green/red (–)

Pink/white

SPEED SENSOR 2P (Orange) CONNECTOR
(Wire side/female terminals)

Green/red

maxiscooter-club.ru

«
...
516
517
518
519
520
...
»

Содержание NSS250A Reflex 2001-2007















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NSS250A Reflex 2001-2007

Бренд: Cobra Страницы: 2

Бренд: hepco & becker Страницы: 2

Бренд: Baja motorsports Страницы: 20

Бренд: Honda Страницы: 141

Бренд: Braaap Страницы: 40

Бренд: Malossi Страницы: 36

Бренд: BMW Страницы: 16

Бренд: Bajaj Страницы: 44

Бренд: DYNATEK Страницы: 4

Бренд: Arai Helmet Страницы: 12

Бренд: GAS GAS Страницы: 52

TXT RACING 2015

Бренд: GAS GAS Страницы: 59

Бренд: GAS GAS Страницы: 56

Бренд: GAS GAS Страницы: 128

Бренд: GAS GAS Страницы: 131

Бренд: HealTech Electronics Страницы: 2

Бренд: Healtech Страницы: 6

Бренд: Shad Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды