GE auisys cs2 Скачать руководство пользователя страница 222

Страница: 222 / 268

Electromagnetic compatibility (EMC)

Changes or modification to this equipment not expressly

approved by the manufacturer could cause EMC issues

with this or other equipment. Contact the manufacturer

for assistance. This device is designed and tested to

comply with applicable regulations regarding EMC as

follows.
Use of portable phones or other radio frequency (RF)

emitting equipment (that exceed electromagnetic

interference levels specified in IEC 60601-1-2) near the

system may cause unexpected or adverse operation.

Monitor operation when RF emitters are in the vicinity.
Use of other electrical equipment adjacent to or stacked

with this system may cause interference. Verify normal

operation of equipment in the system before use on

patients.

Cables

Cables used to obtain system electromagnetic emission and
immunity results are described below.

Use of any cables other than those specified by the

manufacturer may result in increased emissions or

decreased immunity of the anesthesia system.

Display optional output
ports

Cables used for EMC testing

Ethernet

Standard 8-pin RJ45 connector with
unshielded Ethernet cable - 7.6 m maximum
length.

Ethernet

Standard 8-pin RJ45 connector with
unshielded Ethernet cable - 7.6 m maximum
length.

Universal Serial Bus (USB)

Standard Type A connector USB cable with
foil shield - 1.8 m maximum length.

Universal Serial Bus (USB)

The visible USB connector can be populated
with a memory stick.

Video Graphics Array (VGA) Standard VGA 15-pin D-subminiature three

row connector with shielded cable - 1.8 m
maximum length.

RS-232 Serial with On/
STBY

Part number M1023823.

WARNING

•

WARNING

Aisys CS²

11-46

2067226-001

Содержание auisys cs2













































































































































































































































































Результаты поиска

Содержание auisys cs2

Отзывы:

Похожие инструкции для auisys cs2

Бренды по названию

Популярные бренды

GE auisys cs2, Руководство пользователя

Результаты поиска

Содержание auisys cs2

Отзывы:

Похожие инструкции для auisys cs2

Бренды по названию

Популярные бренды