GE auisys cs2 Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 268

background image

Scavenging from an auxiliary manual breathing
circuit

Scavenge the exhaust if an auxiliary manual circuit is used with N2O
or volatile anesthetics.
An auxiliary inlet is available on the AGSS. It provides a female
connection for use with a 30 mm - 30 mm male connector (or 30 mm
- 19 mm male connector) under the breathing system. Do not use
these connectors as an outlet for exhaust flow.
A separate hose is needed to connect the exhaust from the auxiliary
manual breathing circuit to the auxiliary inlet on the AGSS.

Scavenging a gas monitor sample flow

Sample gas from a gas monitor can be scavenged by connecting the
exhaust from the monitor to either the sample gas return port located
on the front of the machine or the tubing connector provided on the
AGSS.

•

To scavenge from a gas monitor using the sample gas return
port, connect the exhaust from the monitor to the sample gas
return port located on the front of the machine.

•

To scavenge from a gas monitor using AGSS, connect tubing
from the monitor to the tubing connector on the bottom of the
AGSS underneath the breathing system.

Sample gas return port

Connect the sample gas exhaust tube to the gas return port. Exhaust
gas will be directed to the scavenging system.

AB.75p127

Aisys CS²

8-14

2067226-001

«
...
144
145
146
147
148
...
»

Содержание auisys cs2













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для auisys cs2

Бренд: GALLERY Страницы: 18

Бренд: ICS Schneider Messtechnik Страницы: 124

Бренд: CAIRE Страницы: 2

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: Madrigal Страницы: 5

Бренд: MacDon Страницы: 504

FlexDraper FD2 Series

Бренд: MacDon Страницы: 2

OXYGEN PRO MINI

Бренд: M-Audio Страницы: 56

QNET Physics and Dynamics

Бренд: Quanser Страницы: 4

Бренд: Samson Страницы: 2

Бренд: Varimixer Страницы: 28

AirForm Night Splint

Бренд: Össur Страницы: 16

Бренд: Össur Страницы: 17

Бренд: Jumil Страницы: 78

Бренд: Ocean Signal Страницы: 2

RadioPRO 4 RP4-MZ11

Бренд: PAC Страницы: 5

Бренд: Lightolier Страницы: 2

OMNIS 2.1006.0010

Бренд: Metrohm Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды