GE auisys cs2 Скачать руководство пользователя страница 231

Страница: 231 / 268

System configuration

Use the

System Config.

menu to set default information for the

system. Use the

System Config.

menu to access menus and

settings for

Colors

Units

Ventilator Settings

Alarm Settings

Parameter Settings

Trends Setup

, and

Pages Setup

Display settings

Use the

Colors

menu to set the default colors for waveforms, digit

fields, and trends.
Use the

Units

menu to set the default units for parameters and

currency.

Setting colors

Set

Paw

Flow

Respiratory

, and

CO2

parameters.

From Super User mode, select

System Config.

and then

Colors

For each parameter, select the desired color from the drop-down
list.

Select

Back

to return to the

System Config.

menu.

Setting units

Set

Patient Weight

CO2

Gas Supply Pressure

Paw

, and

Currency

to the desired units.

Currency

is only available for

systems with the ecoFLOW option installed.

From Super User mode, select

System Config.

and then

Units

For each parameter, select the desired unit from the drop-down
list.

Select

Back

to return to the

System Config.

menu.

Ventilator settings

Use the

Ventilator Settings

menu to set the default user settings for

VCV Cardiac Bypass

Circuit Compliance

Sample

Compensation

, and

TV for Ideal Body Weight

Setting ventilator defaults

From Super User mode, select

System Config.

and then

Ventilator Settings

12 Super user mode

2067226-001

12-5

Содержание auisys cs2













































































































































































































































































Результаты поиска

Содержание auisys cs2

Отзывы:

Похожие инструкции для auisys cs2

Бренды по названию

Популярные бренды

GE auisys cs2, Руководство пользователя

Результаты поиска

Содержание auisys cs2

Отзывы:

Похожие инструкции для auisys cs2

Бренды по названию

Популярные бренды