GE auisys cs2 Скачать руководство пользователя страница 229

Страница: 229 / 268

Gas usage

Use the

Gas Usage

menu to view the total fresh gas usage since the

last reset, to reset the gas usage to zero, and view optional
ecoFLOW and agent cost information.

Resetting cumulative gas usage

From Super User mode, select

Gas Usage

and then

Cumulative Gas Usage

. Gas and agent usage since the last

reset will show.

Select

Reset Usage

. Notice that the gas and agent usage totals

will reset to zero and that

Last Reset

shows the current date.

Select

Back

to return to the

Gas Usage

menu.

Setting ecoFLOW

Use the

ecoFLOW

menu to set the split screen defaults for

FiO2

Setting

FiO2 Line

, and

Agent Cost

. This menu item is only

available on systems with the ecoFLOW option installed.

From Super User mode, select

Gas Usage

and then

ecoFLOW

Select the item to change. Make the change.
For

FiO2 Setting

, set the numeric value for FiO2 on the split

screen.
For

FiO2 Line

, select whether to show or hide the FiO2 line on

the split screen.
For

Agent Cost

, select whether to show or hide the agent

delivered costs on the split screen.

Select

Back

to return to the

Gas Usage

menu.

Setting agent costs

Use the

Agent Costs

menu to modify the currency and agent cost

defaults used to show the cost of agent delivered on the split screen.
This menu item is only available on systems with the ecoFLOW
option installed.

From Super User mode, select

Gas Usage

and then

Agent

Costs

Select the

Currency

from the drop-down list.

Set the cost for each agent.

12 Super user mode

2067226-001

12-3

Содержание auisys cs2













































































































































































































































































Результаты поиска

Содержание auisys cs2

Отзывы:

Похожие инструкции для auisys cs2

Бренды по названию

Популярные бренды

GE auisys cs2, Руководство пользователя

Результаты поиска

Содержание auisys cs2

Отзывы:

Похожие инструкции для auisys cs2

Бренды по названию

Популярные бренды