GE auisys cs2 Скачать руководство пользователя страница 150

Страница: 150 / 268

Installing gas cylinders

Do not leave gas cylinder valves open if the pipeline

supply is in use. Cylinder supplies could be depleted,

leaving an insufficient reserve supply in case of pipeline

failure.

Installing cylinders with pin indexed yokes

Locate the cylinder wrench.

Close the cylinder valve on the cylinder to be replaced.

Loosen the tee handle.

Open the cylinder yoke.

Remove the used cylinder and the used gasket.

Remove the cap (if equipped) from the cylinder valve on the new
cylinder.

Make sure there is only one gasket on the cylinder
connection. No gasket or more than one gasket can
cause a leak.

Install a new gasket.

Align the cylinder post with the index pins.

Close the yoke gate and tighten the tee handle.

10. Make sure there is a cylinder plug and gasket in any empty

cylinder yokes.

11. Complete "

Performing a high-pressure leak test

Installing cylinders with DIN connections

Close the cylinder valve on the cylinder to be replaced.

Loosen the adapter and remove the cylinder.

Remove the cap from the cylinder valve on the new cylinder.

Install the cylinder.

Complete "

Performing a high-pressure leak test

Performing a high-pressure leak test

Turn on the system.

Disconnect pipeline supplies.

CAUTION

WARNING

Aisys CS²

8-18

2067226-001

Содержание auisys cs2













































































































































































































































































Результаты поиска

Содержание auisys cs2

Отзывы:

Похожие инструкции для auisys cs2

Бренды по названию

Популярные бренды

GE auisys cs2, Руководство пользователя

Результаты поиска

Содержание auisys cs2

Отзывы:

Похожие инструкции для auisys cs2

Бренды по названию

Популярные бренды