Daikin UATYQ20-115ABAY1 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 104

Daikin UATYQ20-115ABAY1 Скачать руководство пользователя страница 60

We reserve the right to make changes without prior notice

60

Tipo sbrinamento C3B
SCORREVOLE
Tipo sonda:
PRESSIONE

Defrost type C3B
SLIDING
Probe type:
PRESS.

Tipo descon. C3B
POR PRESIóN
Tipo MODULANTE
Deses.en PRESION

This screen is used to set the defrost mode and the reference probe for defrost control.

Tipo C3C
Refrigerante R410A

Type C3C
Refrigerant R410A

Tipo C3C
Refrigerante R410A

This screen is used to set the refrigerant type in the unit.

C4
Freecooling est. -
Freeheating inv. -
Freecooling inv. -

C4
Sum.Freecooling -
Win.Freeheating -
Win.Freecooling -

C4
Freecooling ver. -
Freeheating inv. -
Freecooling inv. -

This screen is used to enable free cooling and free heating.
The second line is used to enable free cooling in summer mode.
The third line is used to enable free heating in winter mode.
The fourth line is used to enable free cooling in winter mode.

Controllo C5
Freecooling e
freeheating inverno
in TEMPERATURA

Freecooling and C5
winter freeheating
control in
TEMPERATURE

Control C5
Freecooling y
freeheating inv.
en TEMPERATURA

This screen is used to set the free cooling and free heating mode by selecting one of the following options:



Temperature: the mode is managed based on the difference between ambient and external air

temperature;



Enthalpy: the mode is managed based on the difference between ambient and external air enthalpy.

The fourth line is used to set the control mode of free cooling and free heating.

Selezione C6
Est/Inv. AUTOMATICO

Gestione umidità N

Summer/winter C6
selection AUTOMATIC
Humidity
management N

Selección C6
Ver./Inv. PANEL

Gestiòn humed. S

This screen is used to set either manual or automatic management of the shift from summer to winter and to
enable humidity management.
The second line is used to set the shift from summer to winter either manually (using the keyboard) or
automatically.
The fourth line is used to enable management of dehumidification and humidification.

Sonda temperatura C7
interna

Tipo NTC

Internal C7
temperature probe

Type NTC

Sonda temperatura C7
interna

Tipo NTC

This screen is used to set the type of ambient temperature probe.
The fourth line is used to set the probe type.

Sonda temperatura C8
esterna S

Tipo NTC

Enable external C8
temperature probe Y

Type NTC

Sonda temperatura C8
externa S

Tipo NTC

This screen is used to enable the external air temperature probe and to set its type.
The second line is used to enable the external air temperature probe.
The fourth line is used to set the probe type.

«
...
58
59
60
61
62
...
»

Содержание UATYQ20-115ABAY1









































































































Отзывы:

Нет отзывов