Daikin UATYQ20-115ABAY1 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 104

Daikin UATYQ20-115ABAY1 Скачать руководство пользователя страница 56

We reserve the right to make changes without prior notice

56

7.4 Home screen and main menu

As soon as the screen is switched on, the display shows the home screen M1 (the screen code is not
displayed).

Set 27.0°C 50.0% U01

27.0

°C

50.0

%

OFF DA TAST. 10:30

Set 27.0°C U01

27.0

°C

50.0

%

OFF BY KEYB. 10:30

Set 27.0°C 50.0% U01

27.0

°C

50.0

%

OFF P/TECL. 10:30

The first line in the screen shows the setpoints of the ambient temperature and humidity. The address of the
unit is displayed on the right-hand side. For instance, U01 means that the address of the board fitted in the
controller unit is pLAN1.
The second line shows the values of the ambient temperature and humidity measured by the controller probes,
expressed in degrees and percentage.
The last line in the screen shows the status of the unit on the left and the current time on the right.

The other screens in the main branch can be scrolled using the arrow buttons. These are view-only screens
and they summarise the operating status of the unit:

□

indicates that the function is not enabled;

■

indicates that the function is enabled.

Unità in ESTATE M2
Fasce orarie



Deumidifica



Compensazione



Unit in SUMMER M2
Time slot



Dehumidify



Compensation



Unid. en VERANO M2
Franj.horar.



Deshumecta



Compensación



The screen shows whether the unit is running in summer or winter mode, according to the set time slots, in
dehumidification mode and whether setpoint compensation is active based on the external air temperature.

M3
Sbrinamento



Freecooling



Freeheating



M3
Defrost



Freecooling



Freeheating



M3
Desescharche



Freecooling



Freeheating



The screen shows whether the unit is running a defrost cycle and whether free cooling or free heating is
enabled.

Compressore 1



M4

Compressore 2



Compressore 3



Compressore 4



Compressor 1



M4

Compressor 2



Compressor 3



Compressor 4



Compresor 1



M4

Compresor 2



Compresor 3



Compresor 4



The screen shows the enabled compressors in the unit.

Prevent



M5

Limite mandata



Antigelo -

Prevent



M5

Supply limit



Antifreeze -

Prevenc



M5

Limite impuls.



Antihiel -

The screen shows whether the “prevent”, “supply limit” temperature and “anti-freeze” functions are enabled.

Funzionamento M6
ventilatori plug-fan
Mandata Automatico
Ripresa Automatico

Operation M6
Plug-fan
Delivery Automatic
Return Automatic

Operación M6
Ventilad.Plug-fan
Impulsión
Automatico
Retorno Automatico

This screen only appears if the air flow control in the unit has been enabled: it shows the active controller for
the fans in the delivery and return lines.

«
...
54
55
56
57
58
...
»

Содержание UATYQ20-115ABAY1









































































































Отзывы:

Нет отзывов