Carrier VECTOR 6500 Скачать руководство пользователя страница 83

Страница: 83 / 330

62-11389

−

c.Lock / Unlock the Remote Control Panel

LOCKING THE PANEL:

Press and hold the Carrier Logo for

approximately one second and then

release.

The lock indicator light will illuminate.

CARRIER LOGO

LOCK INDICATOR LIGHT

UNLOCKING THE PANEL:

Press the Carrier Logo for 10 seconds

The lock indicator light will de-energize.

d. Pre-setting Set Point With Remote Control Panel

The control panel allows the user to pre-set 5 different temperatures.

NOTE

Once preset set points have been chosen, only those 5 designated set points can be used.

1. Place the unit switch panel mounted Main

Power switch in the desired position.

2. Press Carrier logo and the lock light will illuminate.

3. Press UP ARROW for 10 sec-

onds. P1 will be displayed.

4. Set lowest set point required.

5. Press Carrier logo and P2 will

be displayed. Set next highest

temperature required.
6. Follow same procedure for the

next three temperatures.

Содержание VECTOR 6500











































































































































































































































































































































Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды