manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 239

7

−

106

62-11389

Alarm

NO.

Steps

Alarm/Cause

Corrective Action

243

SUCTION/EVAP CALIBRATE ERROR

•

TRIGGER–ON: There is an error in either or both of the Suction Pressure (CSP) or Evaporator

Pressure (EVOP) Sensor Calibration values stored in the microprocessor memory. Note that neither

of these transducers can be calibrated manually. This is an error in the microprocessor.

•

UNIT CONTROL: Alarm only.

•

RESET CONDITION: Auto Reset when both Suction and Evaporator Pressure transducers are

reading correctly or alarm may be manually reset via keypad or by turning the unit off, then back on

again.

NOTE: Follow the steps below until a problem is found. Once a repair or correction has been made, the active

alarm should clear itself (see reset condition above). Operate the unit through the appropriate modes to see if

any active alarm occurs. Continue with the steps below as necessary.

1

Check Suction Pressure (CSP) and Evaporator Pressure (EVOP) Readings

a. Check Suction and Evaporator

Pressure Readings in the Unit Data.

Must read valid data.

b. Install manifold gauge set and

check and compare compressor

suction & evaporator pressures with

those shown on the microprocessor

display.

Suction and Evaporator Outlet Pressures must have

the same reading on gauges & on microprocessor

display.

NOTE: Microprocessor Suction (CSP) and Evap-

orator (EVOP) pressure readings have a maxi-

mum value of 100 psig (7.5 bar.) The actual pres-

sure must be lower than 100 psig in order to per-

form this test.

2

Reset Microprocessor

a. Place the Main Power switch in the

OFF position for 30 seconds, then

back to the desired position.

Microprocessor powers up OK

b. Wait 2-3 minutes, then check to see if

A-243 becomes active again.

Suction and Evaporator pressure values are reading

OK when compared to test gauges.

Alarm is cleared.

c. Disconnect positive battery cable

from the battery, wait 30 seconds,

then reconnect and place the Main

Power switch in the desired

position.

Microprocessor powers up OK

d. Wait 2-3 minutes, then check to see if

A-243 becomes active again.

Suction and Evaporator pressure values are reading

OK when compared to test gauges.

Alarm is cleared.

e. Valid readings are not appearing for

either or both the Suction and

Evaporator Pressures in the Unit

Data.

Download and replace microprocessor. Refer to

Section 5.7.

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды