manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 241

7

−

108

62-11389

Alarm

NO.

Steps

Alarm/Cause

Corrective Action

248

CONFIGURATION MODE / HP2 ERROR

•

TRIGGER–ON: EEPROM configuration is out of range.

•

UNIT CONTROL: Shutdown and alarm.

•

RESET CONDITION: Auto Reset only when valid info is available for the microprocessor are

entered.

Follow the steps below until a problem is found. Once a repair or correction has been made, clear the alarm(s).

(See Note 1 page 7

−

2.) Operate the unit through the appropriate modes to see if any active alarm occurs.

Continue with the steps below as necessary.

1

Check microprocessor

a. Check set point setting.

Must be between -22 and +89.6

°

F (-30 and +32

°

C.)

b. Enter new set point.

Must be between -22 and +89.6

°

F (-30 and +32

°

C.)

c. Check Functional Parameters.

All settings must be valid.

2

Check Software Revision

a. Check microprocessor software

revision.

Upgrade to the latest revision of software. The latest

revision may contain configurations that were not

present in older revisions.

b. Check Functional Parameters

All settings must be valid. Send desired settings to

microprocessor using the latest version of

ReeferManager or a PC Card (Do NOT use the

keypad.)

c. Check Configurations

All settings must be valid. Send desired settings to

microprocessor using the latest version of

ReeferManager or a PC Card (Do NOT use the

keypad.)

3

Reset microprocessor

a. Place the Main Power switch in the

OFF position for 30 seconds, then

back to the desired position.

Microprocessor powers up OK.

b. Alarm 248 remains active.

Download and replace microprocessor. Refer to

Section 5.7.

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды