Carrier VECTOR 6500 Скачать руководство пользователя страница 130

Страница: 130 / 330

62-11389

−

MessageCenter MESSAGES - Continued

Message

Description

MICRO WILL STOP IN XXX SECONDS

The Main Power switch has been placed in the OFF position and

the system valves are closing. The display will turn off when the

count down reaches zero.

MIN SETPOINT HAS BEEN REACHED

Minimum Set Point allowed by configuration settings has been

reached.

MODIFIED

This message will appear in the MessageCenter along with the cur-

rent IntelliSet indicating that the IntelliSet is active and one or more

of its settings have been modified.

NEW SW: = TO LOAD, TO

↑

CANCEL

A Program PC Card has been inserted into the PC Card slot, and

the program on the PC Card is a newer version than what is al-

ready loaded in the microprocessor. Press the = key to load the

program.

NO ACTION TAKEN, REMOVE CARD

A Program PC Card has been inserted into the PC Card slot, and

no key presses have been made to install the program into the mi-

croprocessor. The PC Card may be safely removed from the slot.

NO ACTIVE ALARMS

There are no active alarms in the microprocessor Alarm List.

NO DATA ON CARD, REMOVE CARD

A Program or Configuration PC Card has been inserted into the PC

Card slot, and no valid data is present on the PC Card. The PC

Card may safely be removed from the unit.

NO DATA TO COPY, REMOVE CARD

A Download PC Card has been inserted into the PC Card slot, and

there is no valid data in the DataLink data recorder to copy onto the

PC Card. The PC Card may safely be removed from the unit.

NO INACTIVE ALARMS

There are no inactive alarms in the Alarm List

NO INSTALLS LEFT, REMOVE CARD

An Option PC Card has been inserted into the PC Card slot, and all

install options have been used. The PC Card may safely be re-

moved from the unit.

OLD INTELLISETS-USE REEFERMAN

The IntelliSets that are on the Configuration PC Card were written

with too old of a PC Program, like ServiceManager. The software in

the micro requires IntelliSets to be written to the Configuration PC

Card using ReeferManager. Rewrite the information to the card us-

ing ReeferManager, then use it in the microprocessor again

OLD SW:CANNOT LOAD-REMOVE CARD A Program PC Card has been inserted into the PC Card slot, and

the major version of the program on the PC Card is an older vers-

ion than what is already loaded in the microprocessor. Software

with older major versions can not be loaded into the micropro-

cessor. Remove the PC Card.

OLD SW, = TO LOAD,

↑

TO CANCEL

A Program PC Card has been inserted into the PC Card slot, and

the minor version of the program on the PC Card is an older ver-

sion than what is already loaded in the microprocessor. Press the =

key to load the older program.

PC MODE

The Main Power switch is in the OFF position, the PC Mode Jump-

er is connected and engine is not running in order to enter PC

Mode.

PM DUE

Preventative Maintenance is now due on the unit.

PRESS

↑↓

TO VIEW DATA

Press the UP or DOWN ARROW key to scroll through the Data

List.

PRESS

↑↓

TO VIEW SETTINGS

Press the UP or DOWN arrow key to scroll through Functional Pa-

rameter Settings.

PRESS

↑↓

TO VIEW PRINT MENU

Press the UP or DOWN arrow key to view the Strip Print setup

menu.

PRESS = TO MARK TRIP START

Press the = key to mark the start of the trip in the DataLink data

recorder.

PRESS = TO START PRETRIP

Press the = key to begin Pretrip tests.

PRESS

↑↓

TO VIEW INTELLISET

Press the UP or DOWN arrow key to view IntelliSet list. This mes-

sage will appear after IntelliSets are installed into the micropro-

cessor, and the unit can not be started until an IntelliSet is selec-

ted.

Содержание VECTOR 6500











































































































































































































































































































































Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды