manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 128

62-11389

6

−

2

MessageCenter MESSAGES - Continued

Message

Description

CARD LOCKED - REMOVE CARD

The lock switch on the PC Card is in the “Locked” position. To use

the PC Card, move the switch to the “Unlocked” position.

CARD REMOVED, DATA NOT COPIED

The PC Card was removed before all data was copied onto the

card.

CARD REMOVED, REINSERT CARD

The PC Card was removed from the card slot before the operation

was completed. Reinsert the PC Card into the card slot to perform

the operation.

CFG: =TO LOAD,

↑

TO CANCEL

A Configuration Card has been inserted into the PC Card slot.

Press the = key to load configurations into microprocessor.

CHANGE INTELLISET TO EXIT

The IntelliSleep IntelliSet is active. Alternates with “IN-

TELLI-SLEEP MODE” at 5 second interval whether unit is running

or not.

CHARGE MODE-HOLD=TO EXIT

Service Mode has the refrigeration system set so that it can be

charged with refrigerant through the liquid line service valve. Press

the = key to manually exit, or wait until the charging is complete.

CHECK AT NEXT SERVICE INTERVAL

The unit needs to be checked at next service interval.
There is currently an active non-shutdown alarm in the alarm list.

CHECK DOOR

Door switch indicates that a refrigerated compartment door is not

closed.

CHECK FUEL LEVEL

(Requires Optional Sensor)

The level in the fuel tank is very close to empty.

CHK WIRES FROM MICRO TO KEYPAD

There is a communication signal lost between the keypad, display

and control module. Check and test the wiring to the keypad/dis-

play

COMPONENT TEST MODE

Pressing the = key while this message is being displayed will allow

user access to Component Test Mode.

CONFIG ERROR, REMOVE CARD

There was an error configuring the microprocessor with the Config-

uration PC Card. Remove the PC Card from the slot.

CONFIGS COMPLETE,= TO EXIT

The user has reached the end of the Configurations List. Pressing

the UP or DOWN ARROW key will start list over. Press the = key

to exit Configuration List.

CONFIGURATION MODE

Press the = key to enter Configuration Mode.

CONFIGURATION NOT CHANGED

New configuration selection was not entered (saved) within the 5

second time limit.

CONTINUOUS LOCKED

The current set point is within a range that has been locked into the

Continuous Run Mode. Start-Stop can not be selected.

CONTINUOUS RUN MODE SELECTED

The unit operating mode has been changed from Start-Stop to

Continuous Run.

COPY COMPLETE, REMOVE CARD XX

A DownLoad PC Card has been inserted into the PC Card slot, and

all data from the DataLink data recorder has been copied onto the

PC Card. You may safely remove PC Card from the slot. XX =

number of empty download slots remaining on the card.

COPY ERROR, REMOVE CARD XX

A DownLoad PC Card has been inserted into the PC Card slot and

an error occurred while the data was being copied onto the PC

Card. You may safely remove the PC Card from the slot.

XX indicates the number of empty download slots remaining on the

card.

COPYING DATA-PLEASE WAIT

A DownLoad PC Card has been inserted into the PC Card slot and

all data from the DataLink data recorder is being copied onto the

PC Card. DO NOT REMOVE THE CARD WHILE THIS MESSAGE

IS BEING DISPLAYED.

DATA RECORDER FAILURE

The microprocessor has stopped recording Unit Data.

DEFROST CYCLE STARTED

The unit has gone into defrost.

DOOR OPEN

A refrigerated compartment door is open.

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды