manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 250

8

−

7

62-11389

DETENT NOTCH

12

1

2

3

4

5

6

7

8

9

10

11

1. Display Board

2. Keypad Support

3. Keypad

4. Latch

5. Spring

6. Bezel

7. Condensate Drain

8. Door

9. Plug

10. Gasket (Window to Bezel)

11. Window

12 Gasket (Keypad to Window)

Figure 8

−

4 Display and Keypad Assembly

b. Reassembly

CAUTION

Do not over torque display & keypad pan

head screws. Torque all screws to 60 in lbs

(6.8 Nm).

NOTE

All gaskets must be replaced any time the

keypad support is removed from the bezel. All

replacement display bezel assembly kits are

packaged with replacement gaskets.

1. Clean all gasket surfaces and install keypad support,

keypad, gaskets and window to the bezel in the cor-

rect order, see Figure 8

−

4 Install the 11 mounting

screws.

2. Install the display board. and reconnect wiring

between the keypad & display assembly and har-

ness.

3. Reconnect negative battery cable and standby plug

as required and run Pretrip to check unit operation.

8.5 ENGINE AND ENGINE RELATED SYSTEMS

SERVICE

Procedures for servicing the engine, fuel system,

engine cooling system and air cleaner are provided in

the following sub-paragraphs.

8.5.1 Fuel System

The fuel system (see Figure 8

−

5) consists of the fuel

tank, mechanical lift pump, fuel filter, fuel injection

pump, the injectors and interconnecting tubing. The fuel

system may also be equipped with an optional electric

pump and/or optional electric fuel heater.

Two fuel system configurations have been used. The

first has the leak-off line at the inlet side of the filter (with

an outlet line check valve) and the second has the

leak-off line at the outlet side of the filter (without an

outlet line check valve).

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды