manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 304

9

−

16

62-11389

YES

NO

YES

YES

NO

NO

NO

YES

NO

NO

NO

YES

NO

YES

NO

YES

NO

YES

NO

YES

YES

YES

NO

NO

YES

YES

YES

NO

YES

NO

START HERE

Is the unit

equipped with two way

communication?

Place the Main Power

switch in the OFF posi-

tion. Does the engine

continue to run?

There a problem with the re-

mote communication  sys-

tem. Repair as necessary.

Disconnect two way

communication from

the unit and install J1

Jumper. This will elim-

inate remote commu-

nication from the sys-

tem.

Check for defective

Main Power switch. Is

Switch defective?

Replace 

defective

switch. Did you find

and correct the condi-

tion?

System OK, re-install

remote communication

disconnected earlier.

Check wiring to the Main Power

switch for an open or short. Did you

find and correct the condition?

Unplug fuel /speed actuator.

Does the unit stop?

Verify the Run Relay de-energ-

izes when the Main Power

switch is placed in the OFF

position.

Check wiring for fuel/speed

actuator for a short. Did you

find and correct the condi-

tion?

Is the relay

defective?

Replace Run

Relay. Did

you find and

correct

the

condition?

Check wiring to Run Relay

for an open or short. Did you

find and correct the condition?

Fuel /speed actuator is

defective or mechanically

seized.

Did the loading

of the software

correct the

problem?

Load current version of

 software from http://www.

transcentral.carrier.com.

Did the software load

correctly?

Verify correct fuel/speed actuator

operation & replace if needed.

Operate system in order to verify

repair. Did you find and correct

the condition.

Remove new fuel/speed

actuator & re-install old

component. Old component is

not the fault.

Remove connectors from unit one at a

time to determine if any other devices

are providing power feedback,

causing the micro to remain powered.

Did you find and correct the condition?

Review the results of

above tests with your

supervisor. If

necessary, go to the

beginning of the tree

& test again.

Go To Condition 8 - Programming

Problems with PC Cards if using a PC

Card to upgrade software. Did the

software load correctly?

System OK,

re-install remote

communication dis-

connected earlier.

NO

Figure 9

−

7 Micro Diagnostic Tree - Condition 3 - Main Power Switch Off - Unit Fails To Stop

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды