Carrier VECTOR 6500 Скачать руководство пользователя страница 129

Страница: 129 / 330

62-11389

−

MessageCenter MESSAGES - Continued

Message

Description

DOOR OPEN - LOW SPEED

A refrigerated compartment door is open forcing the unit to run in

low speed.

ENTERING SERVICE MODE

The initial message for Service Mode.

ERROR: ENG HRS > SWITCH ON

HOURS

When setting up a replacement microprocessor, incorrect hours

have been entered

ERROR: HI SP HRS > TOTAL ENG

HOURS
ERROR: SBY HRS > SWITCH ON SBY

HRS
EVAC / CHARGE MODE

The unit is in Service Mode, and the refrigeration system is ready

to be evacuated then charged with refrigerant. Refer to Section

5.2.3.

EXITING PRETRIP MODE

Pretrip has been aborted either by user or by a pretrip alarm.

EXITING SERVICE MODE

Service Mode has been turned off and unit is returning to normal

operation.

FORCED LOW ENGINE SPEED

Due to current ambient conditions and power requirements, the

engine is being set to operate in Low Speed. (See Section 4.8.3,

step 1 for more information.)

FUNCTION NOT CHANGED

The = key was not pressed in the allotted amount of time to select

the new Functional Parameter setting. The new setting was not

stored and the old setting will be used.

HOUR METERS NOT CHANGED

Indicates that no changes have been made to the hour meters in

either the configuration or functional parameter lists.

INACTIVE ALARMS IN MEMORY

There are inactive alarms in the microprocessor alarm list which

have not yet been cleared.

INSTALLED, REMOVE CARD XX

An Option PC Card has been inserted into the PC Card slot, and

the option has been installed in the microprocessor. The PC Card

may safely be removed from the slot. XX indicates the number of

option installations remaining on card.

INSTALLING OPTION, PLEASE WAIT

An Option PC Card has been inserted into the PC Card slot, and

the option is being installed in the microprocessor. DO NOT RE-

MOVE THE CARD WHILE THIS MESSAGE IS BEING DIS-

PLAYED.

INSTALL STOPPED, REINSERT CARD

An Option PC Card has been inserted into the PC Card slot, and

the install process has been stopped by the PC Card not being fully

inserted in the slot, or by being removed. Remove and reinsert PC

Card to continue.

INTELLI-SLEEP MODE

The IntelliSleep IntelliSet is active. This message alternates with

“CHANGE INTELLISET TO EXIT” at 5 second interval whether unit

is running or not

KEYPAD LOCKED-BATTERY TOO LOW

Once the battery voltage goes below 7.0 Volts for 10 seconds, all

of the keys on the keypad will be locked.

LIST END, = TO CLEAR ALARMS

The end of the Alarm list has been reached. Pressing the = key will

clear the Alarm list.

LOADING INFO

A Configuration PC Card has been inserted into the PC Card slot,

and information from the card is being loaded into the micropro-

cessor. DO NOT REMOVE THE CARD WHILE THIS MESSAGE

IS BEING DISPLAYED.

MAIN MENU

Consists of Configuration Mode, Component Test and Service

Modes.

MAX SETPOINT HAS BEEN REACHED

Maximum set point allowed by configuration settings has been

reached.

MICRO WILL RESET & RESTART NOW

The microprocessor Program software has just been changed, or a

new configuration has been programmed into the microprocessor.

The microprocessor will turn itself off then on again (similar to a

computer reboot) in order for the changes to be effective.

Содержание VECTOR 6500











































































































































































































































































































































Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды