manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 155

7

−

22

62-11389

Alarm

NO.

Steps

Alarm/Cause

Corrective Action

7.5 START UP / ENGINE ALARMS

30

FAILED TO RUN MINIMUM TIME

•

TRIGGER–ON: The unit has shutdown on an alarm 3 times without having run for at least 15

minutes between each shutdown (not including Door shutdowns.)

•

UNIT CONTROL:

Engine Operation: engine and unit shutdown and alarm.

Standby Operation: refrigeration system shutdown and alarm with PSCON

still energized.

•

RESET CONDITION: Alarm may be manually reset via keypad or by turning the unit off, then back on

again. If the Unit Operation configuration is set to Rail Mode, this alarm will reset after 4 hours.

NOTE: Follow the steps below until a problem is found. Once a repair or correction has been made, clear the

alarm(s). (See Note 1 page 7

−

2.) Operate the unit through the appropriate modes to see if any active alarm

occurs. Continue with the steps below as necessary.

Check For Alarms

Check for shutdown alarms.

Alarm conditions must be corrected and the alarm(s)

cleared to continue.

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды