manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 113

62-11389

5

−

11

2. After the unit specific and time sensitive

configuration settings are complete use the

UP or DOWN ARROW keys until

“CONFIGS COMPLETE, = TO EXIT” is

displayed in the MessageCenter. Press the

= key to save.

3. If the Configurations, Functional

Parameters and DataLink data recorder

setup will be set from the keypad and /or

ReeferManager, continue with following

steps.

5.7.4 Configurations Via Keypad

a. Refer to Section 5.2 for a list of available micropro-

cessor Configurations. Refer to Section 5.2.1 for in-

structions on how to access them.

5.7.5 Functional Parameters Via Keypad

a. Refer to Section 3.15 for list of available Micropro-

cessor Functional Parameters and for directions on

how to access them.

b. Leave the microprocessor powered up as you con-

tinue with the next section.

5.7.6 DataLink Data Recorder Via ReeferManager

NOTE

If the factory settings are used, you can skip this

section.

a. Refer to Section 3.19 for list of DataLink data record-

er setups.

b. Connect your computer to the download port of the

unit and start the ReeferManager program (refer to

Section 5.5 step c.). You will need ReeferManager

version 03.08.00

 

or higher.

NOTE

ReeferManager 03.08.00 is REQUIRED in or-

der to view, change and send new features to

and from the microprocessor.

c. In ReeferManager, go to the Serial Operations Tab,

and then click on Data Recorder/Microprocessor

setup button.

d. Select the Sensors to be recorded and whether you

wish averaged or snapshot recordings (averaged is

recommended for all temperature sensors; snap-

shot is recommended for voltage, amperage, &

RPM).

e. When the setup is correct, press the Send button to

send the new settings to the microprocessor.

f. From the “Confirm Send Information” Pop Up, check

the data you want to send and un-check the data you

don’t want to send. Click the OK button.

g. Verify that the settings were sent by waiting for the

confirmation pop up message.

NOTE

If the DataLink data recorder date and time

were not set earlier, they can be set from this

screen by clicking on Tools>Set Date and Time.

5.7.7 Microprocessor Final Checkout

a. Start the unit and allow it to run for a few minutes.
b. While the unit is running, scroll through the Data List

of the microprocessor. Verify that all the data is now

accurately displayed.

c. Initiate a Pretrip test. Allow the unit to complete the

Pretrip and check for any alarms. Make any neces-

sary repairs before returning the unit into service.

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды