Carrier VECTOR 6500 Скачать руководство пользователя страница 64

Страница: 64 / 330

62-11389

−

3.11 VIEW ACTIVE ALARMS

COOL

DEFROST

ALARM

START‐STOP

ALARM LIST

SELECT

MANUAL

DEFROST

HEAT

CONTINUOUS

NO ACTIVE ALARMS

START‐STOP/

CONTINUOUS

ALARM LIGHT

1. Press the ALARM LIST key. If there are no active alarms, “NO ACTIVE

ALARMS” will display for 5 seconds.

3. Press the ALARM LIST or UP ARROW key to scroll through the list of alarms.

4. When you reach the end of the alarm list, “LIST END, = TO CLEAR ALARMS” is displayed

for five seconds.

5. To clear the alarm list, press the = key while “LIST END, = TO CLEAR ALARMS” is being displayed.

“ACTIVE ALARMS LIST CLEAR” is displayed. This will move all Alarms to the Inactive Alarm list.

2. If there are active alarms, the alarm number will be displayed with the letter “A” in front and the

alarm message following. The last alarm that occurred will be the first alarm displayed and so on.

SETPOINT

BOX TEMPERATURE

+34.5 F

-20.0

Alarms are stored in the Alarm List in the micropro-

cessor. Stored alarms may be viewed in the Message-

Center.
For a complete list of alarms, their meanings, and trou-

bleshooting refer to Section 7.

TIP

Another way to clear active alarms is to turn the

microprocessor OFF and then back on using

the Main Power switch

TIP

“CHK WIRES FROM MICRO TO KEYPAD” in-

dicates there is a wiring problem between the

microprocessor and the display module.

Содержание VECTOR 6500











































































































































































































































































































































Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды