manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 54

62-11389

3

−

5

3.4 PRETRIP

COOL

DEFROST

ALARM

START‐STOP

SETPOINT

BOX TEMPERATURE

ALARM LIST

SELECT

MANUAL

DEFROST

HEAT

CONTINUOUS

TEST #1

2. Press the SELECT key until the MessageCenter

displays “PRESS THE = KEY TO START PRETRIP” .

3. Press the = key to start Pretrip

4. Verify that during TEST#1 the complete display is turned on and that all lights on the Light Bar come

on. Verify during Test #2 that the that the buzzer comes on for the first five seconds.

5. The remainder of Pretrip will take 7 to 15 minutes, and will run itself automatically.

START‐STOP/

CONTINUOUS

1. Place the switch labeled ENGINE/OFF/STANDBY in the desired position

OR place the switch labeled START/RUN-OFF in the START/RUN position.

KEYPAD

+34.5 F

-20.0

XX% COMPLETE

Pretrip is a set of tests run by the microprocessor to

check unit operation. It is recommended that a Pretrip

be run prior to loading the trailer. It will indicate a failure

when one is detected.

TIP

A Pretrip can be started at any box temperat-

ure. If Pretrip is started while the unit is in a

Start-Stop off cycle the unit will start during the

course of the test. If the unit is running when

Pretrip is started, it will shutdown for the first

three tests.

TIP

It is always a good idea to clear all alarms from

both Alarm Lists before starting Pretrip. The

technician will then know that any alarms pres-

ent following Pretrip occurred during Pretrip,

and are not old alarms that had not been

cleared.

During the Pretrip test, the MessageCenter displays the

current test number and description and the % of the

test that has been completed. When Pretrip is complete

the MessageCenter will display one of three different

messages:

•

“PRETRIP PASS” 

OR

•

“PRETRIP FAIL IN TEST X” 

OR

•

“PRETRIP FAILED & COMPLETE”. Alarm light

will be on.

Press the ALARM LIST key to review the alarms

triggered by the Pretrip tests.

TIP

The Pretrip test “PASS” of “FAIL” results mes-

sage will stay displayed until any key is

pressed, or until the Main Power Switch is

placed in the OFF position.

Once Pretrip is started, the control panel keys are dis-

abled until Pretrip is completed.

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды