manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 186

62-11389

7

−

53

Alarm

NO.

Steps

Alarm/Cause

Corrective Action

84

CHECK REMOTE ALARM LIGHT

•

TRIGGER–ON: The fault output circuit (amber “check unit” LED’s) to the light bar is shorted. (This

output [3MP19] from the microprocessor is negative, so the circuit will not be shorted to ground, but

is shorted either within the remote alarm light itself, or to a positive wire.)

•

UNIT CONTROL: Engine and Standby Operation: alarm only.

•

RESET CONDITION: Auto Reset when Alarm light current (amp) draw is normal, or alarm may be

manually reset via keypad or by turning the unit off, then back on again.

NOTE: Follow the steps below until a problem is found. Once a repair or correction has been made, the active

alarm should clear itself (see reset condition above). Operate the unit through the appropriate modes to see if

any active alarm occurs. Continue with the steps below as necessary.

1

Check 2-Light Bar Wiring

a. Inspect light bar & connector.

No damage to light bar.

No damage, moisture, or corrosion in connector.

b. Inspect harness & control box

connector pins & terminals. (See

wiring schematic Section 10.)

No physical damage to harness.

No damage, moisture, or corrosion in connectors.

2

Check 2-Light Bar

Check operation of 2-Light Bar

Refer to Section 8.9.3 for information on testing the

2-Light Bar.

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды