Carrier VECTOR 6500 Скачать руководство пользователя страница 240

Страница: 240 / 330

62-11389

−

107

Alarm

NO.

Steps

Alarm/Cause

Corrective Action

245

CANNOT SAVE SETTING

•

TRIGGER–ON: There is an error in sending and saving new settings in the Microprocessor

memory.

•

UNIT CONTROL: Alarm only.

•

RESET CONDITION: Alarm may be manually reset via Keypad or by turning the unit off, then back

on again.

NOTE: Follow the steps below until a problem is found. Once a repair or correction has been made, the active

alarm should clear itself (see reset condition above). Operate the unit through the appropriate modes to see if

any active alarm occurs. Continue with the steps below as necessary.

Check Microprocessor Software Revision

Check microprocessor software revi-

sion.

Will be a 6 digit number, upgrade if required. Refer to

Section 5.4.2.

Reset Microprocessor

a. Place the Main Power switch in the

OFF position for 30 seconds, then

back to the desired position.

b. Check Active Alarm List.

Alarm is cleared - microprocessor is OK.

c. Alarm 245 remains active.

Unit will operate, but changes to the settings will not

be retained in the microprocessor memory. Download

and replace microprocessor. Refer to Section 5.7.

246

EEPROM WRITE FAILURE

•

TRIGGER–ON: here is an error in the ability to write information to be stored in the memory.

•

UNIT CONTROL: Alarm only

•

RESET CONDITION: Alarm may be manually reset via Keypad or by turning the unit off, then back

on again.

NOTE: Follow the steps below until a problem is found. Once a repair or correction has been made, the active

alarm should clear itself (see reset condition above). Operate the unit through the appropriate modes to see if

any active alarm occurs. Continue with the steps below as necessary.

Check Microprocessor

a. Check set point setting.

Must be between -22 and +89.6

F (-30 and +32

C.)

b.Enter new set point.

Must be between -22 and +89.6

F (-30 and +32

C.)

Reset Microprocessor

a. Place the Main Power switch in the

OFF position for 30 seconds, then

back to the desired position.

Microprocessor powers up OK.

b. Alarm 246 remains active.

Download and replace microprocessor. Download

and replace microprocessor. Refer to Section 5.7.

Содержание VECTOR 6500











































































































































































































































































































































Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды