manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 263

8

−

20

62-11389

occurs, switch it back to the “RECOVER/LEAK CHK/

EVAC MODE” (Refer to Section 5.2.3)

10. Purge nitrogen from system at the suction service

valve.

11. Open the vacuum pump valve and start the pump.

Evacuate unit to 500 microns. Close the vacuum

pump valve and shut off the pump. Wait a few minutes

to be sure the vacuum holds below 2000 microns.

12. If vacuum holds below 2000 microns continue to

step 14. If vacuum rises above 2000 microns contin-

ue to step 13.

13. Repeat steps 8 through 11 until the vacuum stays

below 2000 microns.

14. Once the system holds a good vacuum, it is ready to

be charged with refrigerant. Refer to Section 8.6.2.

b. Evacuation of the Low Side

1. Evacuate only after a low side pressure leak check.

(Refer to Section 8.6.3)

2. If possible keep the temperature of the major com-

ponents (condenser, evaporator, compressor and re-

ceiver) above 60

_

F (15.6

_

C) to speed evaporation of

moisture. If the temperature is lower than 60

_

F

(15.6

_

C), ice might form before moisture removal is

complete. Heat lamps, heat guns or alternate

sources of heat may be used to raise system temper-

ature.

3. The recommended method to evacuate the system is

to connect three evacuation hoses with vacuum

pump and vacuum indicator (see Figure 8

−

18).

4. Ensure that the microprocessor MessageCenter dis-

plays “RECOVER/LEAK CHK/EVAC MODE” during

the evacuation and dehydration procedures. (Refer

to Section 5.2.3.) If the microprocessor switches to

charge mode during the process, switch it back to the

“RECOVER/LEAK CHK/EVAC MODE”.

5. Leave the liquid line service valve and the discharge

service valve frontseated and then midseat the suc-

tion service valve.

6. Start the vacuum pump. Evacuate unit until the elec-

tronic vacuum gauge indicates 2000 microns. Close

the vacuum pump valve and shut off the pump. Wait a

few minutes to be sure the vacuum holds.

7. Break the vacuum with dry nitrogen through the liquid

line service valve. Raise system pressure to approxi-

mately 2 psig (0.1 bar). Ensure that the micropro-

cessor does not switch to the Charge Mode. If this oc-

curs, switch it back to the “RECOVER/LEAK

CHK/EVAC MODE” (Refer to Section 5.2.3

8. Purge nitrogen from the low side of the system at the

suction service valve.

9. Open the vacuum pump valve and start the pump.

Evacuate unit to 500 microns. Close the vacuum

pump valve and shut off the pump. Wait a few minutes

to be sure the vacuum holds below 2000 microns.

10. If vacuum holds below 2000 microns continue to

step 12. If vacuum rises above 2000 microns contin-

ue to step 11.

11. Repeat steps 6 through 9 until the vacuum stays be-

low 2000 microns.

12. Once the system holds a good vacuum, open the

compressor discharge service valve and the liquid

line service valve.

13. Start unit and check the refrigerant charge. Refer to

Section 8.6.2.

c. Evacuation of the Compressor

1. Evacuate only after a compressor pressure leak

check. (Refer to Section 8.6.3.)

2 Ensure the unit will not start automatically by dis-

abling any two way communication and placing the

Main Power switch in the OFF position. Disconnect

the high voltage source and lockout/tagout the re-

ceptacle.

3. If possible keep the temperature of the compressor

above 60

_

F (15.6

_

C) to speed evaporation of mois-

ture. If the temperature is lower than 60

_

F (15.6

_

C),

ice might form before moisture removal is complete.

Heat lamps, heat guns or alternate sources of heat

may be used to raise compressor temperature.

4. Connect evacuation equipment to the compressor

suction and discharge service valves. See

Figure 8

−

18.

5. Start the vacuum pump. Evacuate compressor to 500

microns. Close the vacuum pump valve and shut off

the pump. Wait a few minutes to be sure the vacuum

holds. This checks for residual moisture and/or leaks.

6. Once the compressor holds a good vacuum, open the

compressor suction and discharge service valve to

allow refrigerant to enter the compressor.

7. Start unit and check the refrigerant charge. Refer to

Section 8.6.2.

8.7 COMPRESSOR AND UNLOADER SERVICE

8.7.1 Repair or Replacement Determination

Certain operating conditions or refrigeration system

components may be misdiagnosed and subsequently

lead to the determination that the compressor requires

replacement. These conditions or components should

be checked prior

 

to replacing a compressor and after a

replacement compressor is installed to prevent

replacement compressor damage. To determine if

compressor replacement or repair is required, do the

following:
a. If the compressor is operational, check the refrigerant

charge, refer to Section 8.6.2.

b. If the compressor is operational, check operation of

the unloaders, refer to Section 8.7.6.

c. If the compressor is operational, check the system

components as follows:

1. Install gauges to allow reading of receiver, suction

and discharge pressure. See Figure 8

−

18.

2.

Start the unit in cooling so that compressor operates.

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды