manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 40

9

2

−

13

62-11389

15

2

4

7

8

9

10

11

13

14

1

5

6

+34.5 F

-20.0

ALARM LIST

SELECT

MANUAL

DEFROST

START‐STOP/

CONTINUOUS

OFF

STANDBY

ENGINE

3

START/RUN

OFF

STANDBY

ENGINE

I

O

ALTERNATE

CONFIGURATION

12

MAIN POWER

SWITCHES

1. Indicator lights

2. Keypad Door

3. Main Display

4. MessageCenter

5. Keypad

6. Up and Down Arrow Keys

7. Enter Key

8. Manual Defrost Key

9. Alarm List Key

10. Start/Stop-Continuous Key

11. Select Key

12. Switch Board

MAIN POWER SWITCHES

13. Diesel/Off/Engine Standby Switch (DOES)

(Note: switch is labeled

 ENGINE/OFF/STANDBY)

14. START/RUN - OFF Switch (SROS)

15. Diesel Electric Switch (DES)

(Note: switch is labeled STANDBY/ENGINE)

Figure 2

−

10 Display And Keypad Assembly

b. Main Display, MessageCenter & Indicator Lights

 (see figure Figure 2

−

10)

Indicator Lights

The display has six LEDs across the top to indicate

operational status. These indicators are:

Heat Indicator (Amber) - Illuminated when the unit is in

Heat Mode.

Cool Indicator (Green) - Illuminated when the unit is in

Cool Mode.

Defrost Indicator (Amber) - Illuminated when the unit is

in Defrost Mode.

Alarm Indicator (Red) - Off or Flashes at a rate of 0.5

seconds.

Start-Stop Indicator (Green) - Illuminated when

Start-Stop Operation has been selected.

Continuous Indicator (Green) - Illuminated when

Continuous Operation has been selected.

NOTE

When the unit is in Null mode (fan only), the

mode indicators (cool, heat and defrost) are all

off.

NOTE

There is an opening between the Alarm and

Start-Stop LEDs that is not used at this time.

Main Display

The microprocessor will display the refrigerated

compartment set point to the left and compartment

temperature to the right. Temperatures will be displayed

as signed (+ or -). The microprocessor may be

configured to display the set point in either whole

numbers or with tenths of a degree. The compartment

temperature will be followed by a letter indicating the

information is in degrees Fahrenheit (F) or degrees

Centigrade (C).

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды