manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 62

62-11389

3

−

13

3.9 MANUAL DEFROST

COOL

DEFROST

ALARM

START‐STOP

SETPOINT

BOX TEMPERATURE

ALARM LIST

SELECT

MANUAL

DEFROST

HEAT

CONTINUOUS

DEFROST CYCLE STARTED

+34

START‐STOP/

CONTINUOUS

DEFROST LIGHT

Press the MANUAL DEFROST key. The DEFROST light will come on and the Messa-

geCenter will display “DEFROST CYCLE STARTED” for 5 seconds, or flash “CANNOT

START DEFROST CYCLE” for five seconds.

dF

When defrost mode cannot be manually initiated “CAN-

NOT START DEFROST CYCLE” is displayed in the

MessageCenter. This will occur when:

•

DTT is above 40

°

F (4

°

C). Defrost may be entered

any time the DTT is below 40

°

F (4

°

C) 

OR

•

The engine has not run 15 seconds after starting 

OR

•

The unit is in PC Mode 

OR

•

The unit is in Pretrip 

OR

•

There is an active shutdown Alarm.

TIP

The Manual Defrost Key can be used at any

time to start a Defrost Cycle as long as the pre-

ceding conditions are met.

NOTE

Refer to Section 4.6 for more detailed informa-

tion on DEFROST.

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды