manualshive.com logo in svg

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Carrier VECTOR 6500 Скачать руководство пользователя страница 46

9

2

−

19

62-11389

2.13 SAFETY DEVICES

The system is protected from high pressure conditions which may occur when exposed to very high temperatures

(such as a fire) by a fusible plug mounted in the receiver. Under very high temperature conditions (refer to Section

2.10) the plug will melt, releasing the refrigerant pressure.
System components are protected from damage caused by unsafe operating conditions by automatic shut-down of

the unit when such conditions occur. This is accomplished by the safety devices listed in the following table.

Unsafe Conditions

Safety Device

Device Setting

Excessive operating pressure

High Pressure Switch

(HPS)

Refer to Section 2.10

Excessive current draw by microprocessor

Fuse (F1)

Opens at 7.5 amps

Excessive current draw by speed relay

Fuse (F2)

Opens at 10 amps

Excessive current draw by run relay

Fuse (F3)

Opens at 7.5 amps

Excessive current draw by battery output

Fuse (F5)

Opens at 80 amps

Excessive current draw by control circuit

Fuse (F6)

Opens at 15 amps

Excessive current draw by battery charger in-

put - 20 amp charger.

Fuse (F7, F8)

Opens at 3 amps (single charger) 

OR

opens at 6amps (dual chargers)

See note.

Excessive current draw by battery charger in-

put - 40 amp charger(s).

Fuse (F7, F8, F29)

Opens at 5 amps (timed)

Excessive current draw by generator/power

supply contactors

Fuse (F9)

Opens at 10 amps

Excessive current draw by evaporator heaters Fuse (F10/F11/12)

Opens at 12 amps

Excessive current draw by fuel heater circuit

Fuse (F19)

Opens at 20 amps

Excessive current draw by fuel level sensor

circuit

Fuse (FLS)

Opens at 3 amps

Excessive current draw by evaporator or con-

denser fan motor

Fuse (F26/F27/F28)

Opens at 12 amps

Excessive condenser fan motor winding

temperature

Internal protector

Auto reset

Excessive compressor motor winding

temperature

Internal protector

Auto reset

Excessive evaporator motor winding

temperature

Internal protector

Auto reset

NOTE: When a second 20 amp rated charger is used to charge a lift gate battery, the higher rated fuse is installed

Содержание VECTOR 6500











































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды