Carrier VECTOR 6500 Скачать руководство пользователя страница 293

Страница: 293 / 330

−

62-11389

Indication/Trouble

Possible Causes

Action/Refer-

ence Section

9.4.4 Unit Will Not Terminate Cooling

Unit fails to stop cooling

Temperature sensor malfunction

8.9.10

Contactor (CCON) stuck closed

Check

Microprocessor improperly set

Check set point

Check whether

microprocessor

is set at

C or

9.4.5

Unit Will Not Heat Or Has Insufficient Heating

Unit will not heat or has insuffi-

cient heat

Heater(s) defective

8.9.5

Heater contactors or coil defective

Replace

Defective wiring / connectors

Replace

Loose terminal connections

Tighten

Low voltage

9.3

No or restricted air flow

9.4.10

Temperature sensor malfunction

8.9.10

Compressor contactor stuck closed

Check

9.4.6 Unit Will Not Terminate Heating

Unit fails to stop heating

Microprocessor temperature improperly set

Reset

Microprocessor malfunction

9.6

Temperature sensor malfunction

8.9.10

9.4.7 Defrost Cycle Malfunction

Will not initiate defrost

automatically

Defrost timer has not expired

Check/Reset

Defrost air switch (DAS) malfunction

8.8.9

DTT is above 40

F (4.4

Cool Down

Loose terminal connections (DAS)

Tighten

Will not initiate defrost manually

Keypad defective

8.4.4

Loose terminal connections between keypad and micro-

processor

Tighten

DTT is above 40

F (4.4

Cool Down

Unit has been running less than 15 seconds

Try again

Initiates but does not defrost

Heater contactor or coil defective

Replace

Heater(s) burned out

8.9.5

Evaporator fan contactor stuck closed

Check

Frequent defrost

Defrost air switch (DAS) out of adjustment

8.8.9

Wet load

Normal

Does not terminate or

cycles on defrost.

Defrost air switch (DAS) out of adjustment

8.8.9

DTT malfunction

8.9.10

Refrigerated Compartment

Hot Load

Allow time to

pull down

Defective or insufficient refrigerated compartment insula-

tion or air leak

Correct

Содержание VECTOR 6500











































































































































































































































































































































Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды