Carrier VECTOR 6500 Скачать руководство пользователя страница 123

Страница: 123 / 330

62-11389

−

Table 5

−

2. Microprocessor Configurations - Continued

Configuration

Selections

Description

REMS1 (Remote Switch 1)
OR
REMS2 (Remote Switch 2)

NOTE

If the configuration is set for a

switch, not for a panel, the following

sub configuration will also be avail-

able.

NOT INSTALLED

DOOR OPEN

SWITCH OPEN
DOOR OPEN

SWITCH CLOSED
SWITCH ON

CONTACTS OPEN
SWITCH ON

CONTACTS

CLOSED
REMOTE PANEL

Switch not installed = There is no remote switch or

panel.
DOOR OPEN SWITCH OPEN = The remote switch

will be used as a door switch. The switch contacts

will be OPEN whenever the door is OPEN.
DOOR OPEN SWITCH CLOSED = The remote

switch will be used as a door switch. The switch

contacts will be CLOSED whenever the door is

OPEN.
SWITCH ON CONTACTS OPEN = The remote

switch will be used as a remote control switch. The

switch contacts will be OPEN whenever the switch

is in the ON position.
SWITCH ON CONTACTS CLOSED = The remote

switch will be used as a remote control switch. The

switch contacts will be CLOSED whenever the

switch is ON.
REMOTE PANEL = If set to this value, the remote

panel SYSTEM ON/OFF key will be enabled. The

switch panel mounted Main Power Switch must be

toggled out of the OFF position and the remote

panel SYSTEM ON/OFF key must be pressed for

the unit to operate. However, if the Override Re-

mote Switch 1 or 2 Functional Parameter is set to

YES, the remote panel is disabled.

•

REMS1
OR

•

REMS2

ALARM ONLY

UNIT SHUTDOWN
LOW ENGINE

SPEED

DATA RECORDER

ONLY

ALARM ONLY = When the switch is activated, a

warning alarm will be displayed in the Message-

Center.
UNIT SHUTDOWN = When the switch is activated,

a warning alarm will be displayed in the Message-

Center, and the unit will shutdown.
LOW ENGINE SPEED = When the switch is activ-

ated, the engine will be forced to low speed.
DATA RECORDER ONLY = The DataLink data re-

corder will record every time the the switch is activ-

ated. There will be no alarms or messages dis-

played in the MessageCenter.

SET TIME

Indicates to the microprocessor the time and date for the DataLink data

recorder Real Time Clock .

•

MONTH

1-12

Select the correct month of the year.

•

DAY

1-31

Select the correct day of the month.

•

YEAR

1998 - 2037

Select the correct year.

•

HOURS

0-23

Select the correct hour (0-11 is AM / 12-23 is PM)

•

MINUTES

0-59

Select the correct minute.

Содержание VECTOR 6500











































































































































































































































































































































Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды

Carrier VECTOR 6500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание VECTOR 6500

Отзывы:

Бренды по названию

Популярные бренды