Basler BE1-951 Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 424

background image

6-12

Reporting and Alarm Functions

BE1-951

Setting the Breaker Status Reporting Function

Since the relay is completely programmable, it’s necessary to program which logic variable monitors breaker
status. This is done with the SB-LOGIC (setting breaker, logic) command. Note that even though a BESTlogic
expression is used to make this setting, this setting isn’t included in the section on BESTlogic settings. The
SB-LOGIC command is included here because it is related to breaker monitoring. Section 7,

BESTlogic

Programmable Logic has more information about programming the relay with BEST LOGIC.

Table 6-6. Breaker Status Reporting Settings

Setting

Range/Purpose

Default

Breaker Closed Logic

OR logic expression that is TRUE when the breaker is
closed (e.g., 52a logic).

/IN1

SB-LOGIC Command

Purpose:

Read or set breaker status logic.

Syntax:

SB-LOGIC[=<Breaker Closed Logic>]

Comments: breaker close logic = BESTlogic term that is TRUE when the breaker is closed (i.e., 52a logic)

See Table 6-6 for SB-LOGIC settings information.

SB-LOGIC Command Example
1.

Set the relay to monitor input 3 so that when the breaker is closed, the input is FALSE. (The 52b contact
is wired to IN3.)

>SB-LOGIC=/IN3

Retrieving Breaker Status and Operation Counter Information

Current breaker status can be read from HMI screen 1.5.6 and through the communication ports using the
RG-STAT command. The General Status Reporting subsection provides more information about this
command.

The number of breaker operations can be read at HMI screen 4.3.1. The counter value can be adjusted
using the Edit key. This allows the relay counter value to be matched to an existing mechanical cyclometer
on a breaker mechanism. Write access to the reports functions must be gained to edit this value at the HMI.
Breaker operations can be read or set through the communication ports using the RB-OPCNTR (report
breaker, operations counter) command.

RB-OPCNTR Command

Purpose:

Read or set breaker operations counter.

Syntax:

RB-OPCNTR[=<#operations>]

Comments: #operations = number of breaker operations recorded (0-99999)

If the counter exceeds 99999, the counter will wrap back to 0.

RB-OPCNTR Command Examples

1.

Read the number of breaker operations.
>RB-OPCNTR

14

2.

Synchronize the relay breaker operations counter with an external counter reading of 65 operations.
>RB-OPCNTR=65

NOTE

When the NOT symbol (/) is used, the symbol is applied to
the variable immediately following the symbol.

Courtesy of NationalSwitchgear.com

«
...
130
131
132
133
134
...
»

Содержание BE1-951









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-951

Бренд: CRESTO Страницы: 12

Бренд: K40 Страницы: 20

Бренд: Loewe Страницы: 40

Бренд: Crye Precision Страницы: 28

Бренд: Samsung Страницы: 195

Бренд: IFM Страницы: 5

Бренд: Watlow Страницы: 2

Бренд: Array Solutions Страницы: 2

Бренд: IPGARD Страницы: 2

Бренд: Toshiba Страницы: 59

Бренд: Toshiba Страницы: 97

HLS6186W - 61" Rear Projection TV

Бренд: Samsung Страницы: 4

Бренд: Samsung Страницы: 2

Бренд: Trox Technik Страницы: 4

Бренд: Gymnova Страницы: 4

Бренд: ITech Страницы: 9

DS-KABD8003-RS3/S

Бренд: HIKVISION Страницы: 2

Бренд: Beta Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды