Basler BE1-951 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 424

background image

APPLICATION

PROGRAM

FIRMWARE

VERSION

Change

iv

Introduction

BE1-951

1.50.00/4-5-00

This version was released to provide major upgrades to the original
functionality provided by BE1-951 Overcurrent Protection System and was
mailed to all purchasers.

Added support (metering and recording) for optional VX, Auxilliary Voltage
input sensing. Added or revised the following functions associated with this
input:

Added 25/25VM, Sync Check with Voltage Monitor function.

Added 27X, Auxiliary Undervoltage element.

Revised 59X, Auxiliary Over voltage function to allow it to monitor the
frequency measured on the VX, Auxiliary Voltage input.

Added or revised the following additional protection and control functions:

Added 24, Volts/Hertz Overexcitation element.

Added 67, Directional Control for all Over current tipping elements.

Added or revised the following additional reporting and alarm functions:

Added Distance to Fault function.

Added optional load profile recording function.

Revised the COMTRADE oscillographic recording function to allow the 240
cycles of oscillographic memory to be partitioned into 6 to 16 records.
Added *.HDR, COMTRADE header file to record the fault summary and
active settings associated with the fault.

Revised power fail recovery logic and self diagnostics function to prevent
inadvertent resets of the microprocessor when operated on marginal AC
power supply source.

Added or revised the following communications functions:

Corrected bugs in Modbus protocol.

1.02.02/4-7-00

This version was released after release of version 1.50.00, which was a major
upgrade in functionality for the relay. This version was released to correct bugs
in the original functionality and was mailed to all purchasers of the BE1-951
Over current Protection System.

Revised power fail recovery logic and self diagnostics function to prevent
inadvertent resets of the microprocessor when operated on marginal AC
power supply source.

Corrected bugs in Modbus protocol.

Revised the COMTRADE oscillographic download function to prevent an
invalid COMTRADE file from being created if the oldest record is being
overwritten by a trigger in the middle of the process of transferring the file.

Courtesy of NationalSwitchgear.com

«
...
3
4
5
6
7
...
»

Содержание BE1-951









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-951

Бренд: Sharp Страницы: 108

Бренд: StemRad Страницы: 19

Бренд: soloprotect Страницы: 10

Бренд: STI Страницы: 2

Бренд: Magnum Dimensions Страницы: 2

Бренд: K40 Страницы: 20

Бренд: Faster Страницы: 46

Compass Product Line

Бренд: Image Diagnostics Страницы: 14

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренд: Joslyn Страницы: 2

Бренд: Zenith Страницы: 60

Бренд: Mitsubishi Страницы: 38

Бренд: Mitsubishi Страницы: 36

Бренд: Mitsubishi Страницы: 44

Бренд: Mitsubishi Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды