manualshive.com logo in svg

Basler BE1-951, Инструкция по эксплуатации

Инструкция по эксплуатации для Basler BE1-951 - бесплатное руководство для пользователей, которое можно скачать с нашего сайта. Этот мануал поможет вам настроить и использовать ваш продукт наилучшим образом. Не теряйте время, загрузите его прямо сейчас и начните с эксплуатацией Basler BE1-951.

Поделиться
Скачать
background image

BE1-951

Protection and Control

4-43

Figure 4-25.  Sync-Check Element

recognizes that a non-blocked low set (50TP or 50 TN) element picked up and reset before timing out to trip.
Table 4-33 summarizes the zone sequence coordination settings.

Table 4-33. Zone Sequence Coordination Settings

Function

Range/Purpose

Zone Pickup Logic

The zone sequence pickup logic defines which logic elements should be
considered zone sequence pickups. Only OR (+) logic can be used—no
AND (

9

) variables may be used.

SP-79ZONE Command

Purpose:

Read or set the 79 Zone Sequence Logic.

Syntax:

SP-79ZONE[=<Zone Pickup Logic>]

Comments: A logic zero disables zone sequence coordination.  See Table 4-31 for SP-79ZONE settings

information.

SP-79ZONE Command Example
1.

Increment the 79 automatic reclose count if one or more 50 phase or neutral elements picks up and
all are cleared without a Trip operation.
>SP-79ZONE=50TNPU

Recloser zone sequence coordination detects when a fault has been cleared by a downstream recloser and
increments the upstream 79 automatic reclose count to maintain a consistent count with the other recloser.
A fault is presumed cleared downstream when one or more protective functions pickup and dropout with no
trip occurring. If the zone pickup logic becomes TRUE and then FALSE without a trip output operating, then
the 79 automatic reclose counter should be incremented.  The shot counter is reset by the max cycle timer.
So its 79ZONE is used, this function cannot be disabled.

SYNCHRONISM CHECK PROTECTION

25 Synchronism Check 

Figure 4-25 illustrates the inputs and outputs of the Sync-Check element.  Element operation is described
in the following paragraphs.

The Sync-Check element has one output: 25. When
monitored voltage between the systems as measured by
the phase VTs and the auxiliary Vx input circuits meets
angle, voltage, and slip criteria, the 25 output becomes
TRUE.  

The Block (BLK) input is used to disable Sync-Checking.
A BESTlogic expression defines how the BLK input
functions. When this expression is true, the element is
disabled by forcing the outputs to logic 0. This feature
functions in a similar way to the torque control contact of
an electromechanical relay.

The 25 element is enabled or disabled by the mode input. Two modes are available, Selecting Mode 0
disables the 25 element. Mode 1 enables the 25 element. 

The 25 function module will change the 25 output to TRUE if the following conditions are met:

a) Phase angle between systems is less than setting. 

b) Frequency error between systems is less than setting. As an additional parameter, the relay can

be set to only allow generator frequency greater than bus frequency.

c)

Voltage magnitude between systems is less than setting (the voltage used by the relay for this
feature is a voltage magnitude measurement, not a voltage phasor measurement).

Courtesy of NationalSwitchgear.com

Содержание BE1-951









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-951

Infinite Transtector DPR RACK Installation Instructions preview
Transtector DPR RACK
Бренд: Infinite Страницы: 2
Philips matchline 50PP8421 Specifications preview
matchline 50PP8421
Бренд: Philips Страницы: 2
Philips MatchLine 46PP9527 Brochure & Specs preview
MatchLine 46PP9527
Бренд: Philips Страницы: 2
Philips MatchLine 46PP8621 Specification preview
MatchLine 46PP8621
Бренд: Philips Страницы: 2
Philips MATCH LINE 55PP925 Specifications preview
MATCH LINE 55PP925
Бренд: Philips Страницы: 2
Philips Magnavox 9P6444C Specification Sheet preview
Magnavox 9P6444C
Бренд: Philips Страницы: 2
Philips Magnavox 9P6040C Specification Sheet preview
Magnavox 9P6040C
Бренд: Philips Страницы: 2
Philips Magnavox 9P6044C Specification Sheet preview
Magnavox 9P6044C
Бренд: Philips Страницы: 2
Philips Matchline 41GR8840 Operating Instructions Manual preview
Matchline 41GR8840
Бренд: Philips Страницы: 22
Philips MAGNAVOX MX5472C101 Instructions For Use Manual preview
MAGNAVOX MX5472C101
Бренд: Philips Страницы: 60
Philips MAGNAVOX TP4830 Owner'S Manual preview
MAGNAVOX TP4830
Бренд: Philips Страницы: 48
Datalogic 21069-04 Operating Instructions Manual preview
21069-04
Бренд: Datalogic Страницы: 16
Schörghofer & Frehe Plisse Manual preview
Plisse
Бренд: Schörghofer & Frehe Страницы: 20
Keysight Y1234A Installation Manual preview
Y1234A
Бренд: Keysight Страницы: 2
Watts BA BM Installation And Operation Manual preview
BA BM
Бренд: Watts Страницы: 64
IPC C-103EM Instruction Manual preview
C-103EM
Бренд: IPC Страницы: 20
Philips 55P828899 Directions For Use Manual preview
55P828899
Бренд: Philips Страницы: 54
Philips 55P 9161 Instructions For Use Manual preview
55P 9161
Бренд: Philips Страницы: 60

Бренды по названию

Популярные бренды

Загрузить еще бренды