manualshive.com logo in svg

Basler BE1-951, Инструкция по эксплуатации

Инструкция по эксплуатации для Basler BE1-951 - бесплатное руководство для пользователей, которое можно скачать с нашего сайта. Этот мануал поможет вам настроить и использовать ваш продукт наилучшим образом. Не теряйте время, загрузите его прямо сейчас и начните с эксплуатацией Basler BE1-951.

Поделиться
Скачать
background image

BE1-951 ASCII 

Command 

Interface

11-1

SECTION 11 • ASCII COMMAND INTERFACE

INTRODUCTION

Relay and power system information can be retrieved from a remote location using the ASCII command
interface. The ASCII command interface is also used to enter settings, retrieve reports and metering
information, and perform control operations.  A communication port on the relay front panel provides a
temporary, local interface for communication.  Communication ports on the rear panel provide a permanent
communication interface.

Front and rear panel communication ports can be connected to computers, terminals, serial printers,
modems, and intermediate communication/control interfaces such as RS-232 serial multiplexors.  BE1-951
communication protocols support ASCII and binary data transmissions. ASCII data is used to send and
receive human readable data and commands. Binary data is used for computer communication and
transmission of raw oscillographic fault data if available.

Modbus™, DNP, and other common protocols are also available. Available communication protocol
instruction manuals include 9 3289 00 991 for Modbus

TM

 and 9 3289 00 992 for DNP 3.0. For information

about other protocols, consult your Basler Electric Representative.

Note

Hyperterminal as shipped with Windows® 98 , either first or second edition, cannot be used
for communications with the relay due to a problem introduced in the Windows® 98 version
of Hyperterminal.  The software bug is associated with the carriage return/line feed function
when acting as a terminal emulator.  An upgrade to Hyperterminal that fixes the problem
is available from the Microsoft’s source of Hyperterminal (Hilgraeve Inc.)  at

www.hilgraeve.com

.  The upgrade is referred to as “Hyperterminal-Private Edition.”

Companies that download and use this software must review the terms and conditions
associated with the use of the software.  

SERIAL PORT

Communication connections consist of two Data Communication Equipment (DCE) RS-232 ports, one
RS-485 port, and an IRIG port.  BE1-951 communication protocol is compatible with readily available
modem/terminal software.  If required, password protection provides security against unauthorized operation.
Detailed information about making communication connections is provided in Section 12, 

Installation.

Communications port setup is covered in this section.  Security settings are covered in Section 9, Security.

RS-232 Ports

Two female RS-232 (DB-9) connectors are provided.  One port is located on the front panel and is
designated COM0.  Another port is located on the rear panel and is designated COM1.  Both ports support
full-duplex operation.  Polled operation is possible at the rear port using a simple RS-232 splitter if a polling
address is programmed for COM1.

RS-485 Port

RS-485 terminal block connections are located on the rear panel and designated COM2.  This port supports
half-duplex, multi-drop operation.  Multi-drop (polled mode) operation is possible if a polling address is
programmed for the port.

Courtesy of NationalSwitchgear.com

Содержание BE1-951









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-951

Panasonic NA40-6-H Instruction Manual preview
NA40-6-H
Бренд: Panasonic Страницы: 1
Panasonic NA40 Series Instruction Manual preview
NA40 Series
Бренд: Panasonic Страницы: 1
Panasonic TY-PG70LF50 Fitting Instructions Manual preview
TY-PG70LF50
Бренд: Panasonic Страницы: 56
Magnavox 50ML8105D - Quickuse Specifications preview
50ML8105D - Quickuse
Бренд: Magnavox Страницы: 2
Magnavox 50ML6200D - 50" Rear Projection TV User Manual preview
50ML6200D - 50" Rear Projection TV
Бренд: Magnavox Страницы: 41
Magnavox TS2560 Owner'S Manual preview
TS2560
Бренд: Magnavox Страницы: 32
Magnavox FP5210 Owner'S Manual preview
FP5210
Бренд: Magnavox Страницы: 48
Magnavox 6P4830 Owner'S Manual preview
6P4830
Бренд: Magnavox Страницы: 48
Sony GRAND WEGA KF-50SX200 Instruction Manual preview
GRAND WEGA KF-50SX200
Бренд: Sony Страницы: 251
Zenith Z52SZ80 Service Manual preview
Z52SZ80
Бренд: Zenith Страницы: 40
Zenith PV5268RK and warranty Operating Manual And Warranty preview
PV5268RK and warranty
Бренд: Zenith Страницы: 52
Leader LC 2132 Instruction Manual preview
LC 2132
Бренд: Leader Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды