manualshive.com logo in svg

Basler BE1-951, Инструкция по эксплуатации

Инструкция по эксплуатации для Basler BE1-951 - бесплатное руководство для пользователей, которое можно скачать с нашего сайта. Этот мануал поможет вам настроить и использовать ваш продукт наилучшим образом. Не теряйте время, загрузите его прямо сейчас и начните с эксплуатацией Basler BE1-951.

Поделиться
Скачать
background image

BE1-951

Protection and Control

4-57

virtual switch can be operated both locally from the HMI and remotely from a substation computer or modem
connection to an operator’s console.

The breaker control switch emulates a typical breaker control switch with a momentary close, spring return,
trip contact (output 101T), a momentary close, spring return, close contact (output 101C), and a slip contact
(output 101SC). The slip contact output retains the status of the last control action. That is it is FALSE (open)
in the after-trip state and TRUE (closed) in the after-close state. Figure 4-39 shows the state of the 101SC
logic output with respect to the state of the 101T and 101C outputs.

When the virtual control switch is controlled to trip, the 101T output pulses TRUE (closed) for approximately
200 milliseconds and the 101SC output goes FALSE (open). When the virtual control switch is controlled
to close, the 101SC output pulses TRUE (closed). The status of the slip contact output is saved to
nonvolatile memory so that the relay will power up with the contact in the same state as when the relay was
powered down. 

BESTlogic Settings for 101 Virtual Breaker Control Switch

Virtual selector switch logic settings enable the 101 element by selecting the mode of operation. These logic
settings are listed in Table 5-44. There are no logic inputs. The user label for the 101 virtual breaker control
switch is entered using the SB-LOGIC command. More information about the SB-LOGIC command is
provided in Section 6, 

Reporting and Alarms Functions, Breaker Monitoring.

Table 4-44. 101 Virtual Selector Switch BESTlogic Settings

Function

Range/Purpose

Default

Logic Mode

0 = Disabled, 1 = On/Off

0

BESTlogic settings for the 101 function are made through the ASCII command interface using the SL-101
(settings logic-101 switch) command.

SL-101 Command

Purpose:

Read or set the logic for virtual breaker switch 101.

Syntax:

SL-101[=mode]

SL-101 Command Example
1.

Read the 101 logic.
>SL-101

1

The returned setting indicates that the 101 element is enabled.

Select Before Operate Control of Virtual Breaker Control Switch

The state of each virtual selector switch can be controlled at the HMI through screen 2.2.1. Control is also
possible through the ASCII command interface by using the select-before-operate commands CS-101
(control select-virtual control switch) and CO-101 (control operate-virtual controls switch). A state change
takes place immediately without having to execute an exit-save settings command.

CS/CO-101Command

Purpose:

Select and operate the virtual control switch.

Syntax:

CS/CO-101[=<action>]

Comments: action = T to pulse the 101T output, C to pulse the 101C output

The virtual switch control commands require the use of select-before-operate logic. First, the command must
be selected using the CS-101 command. After the select command is entered, there is a 30 second window
during which the CO-101 control command will be accepted. The control selected and the operation selected
must match exactly or the operate command will be blocked. If the operate command is blocked, and error
message is output.

Courtesy of NationalSwitchgear.com

Содержание BE1-951









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-951

TAZ LOV3 Manual preview
LOV3
Бренд: TAZ Страницы: 19
ABB RET630 Product Manual preview
RET630
Бренд: ABB Страницы: 68
ABB VE5-1 Operating Instructions preview
VE5-1
Бренд: ABB Страницы: 2
ABB Relion 650 Series REL650 Commissioning Manual preview
Relion 650 Series REL650
Бренд: ABB Страницы: 176
ABB REL650 A11 Product Manual preview
REL650 A11
Бренд: ABB Страницы: 118
ABB REL-300 Instruction Manual preview
REL-300
Бренд: ABB Страницы: 184
ABB MDAR Instruction Manual preview
MDAR
Бренд: ABB Страницы: 125
ABB REL670 2.2 IEC Applications Manual preview
REL670 2.2 IEC
Бренд: ABB Страницы: 908
ABB REG316 4 Series Operating Instructions Manual preview
REG316 4 Series
Бренд: ABB Страницы: 980
Guardian 15225 Instruction Manual preview
15225
Бренд: Guardian Страницы: 8
Guardian 01600 Instruction Manual preview
01600
Бренд: Guardian Страницы: 8
TOOLCRAFT EN166 Operating Instructions preview
EN166
Бренд: TOOLCRAFT Страницы: 2
ABB Relion REG670 Product Manual preview
Relion REG670
Бренд: ABB Страницы: 146
Zenith PV4661BG and warranty Operating Manual And Warranty preview
PV4661BG and warranty
Бренд: Zenith Страницы: 48
Sears 626.54528690 Series Owner'S Manual preview
626.54528690 Series
Бренд: Sears Страницы: 36
BLUEMONT NOAQ Boxwall BW50 User Instructions preview
NOAQ Boxwall BW50
Бренд: BLUEMONT Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды