Basler BE1-951 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 424

background image

4-40

Protection and Control

BE1-951

Figure 4-22. 79SCB Logic

Recloser Reset (79RST). The 79RST provides reset indication and is true when the recloser is in the reset
position.

Recloser Sequence Controled Block (79SCB). This
output becomes TRUE when either the 52 status input
OR the 79C input is TRUE AND the sequence
operation (shot counter) matches one of the
programmed steps of the S<g>-79SCB command.
Figure 4-22 illustrates 79SCB logic. See Figures 4-17
and 4-18 for more details.

Recloser BESTlogic Settings

Reclosing is added to a protection scheme by enabling
the Recloser element and connecting the inputs to the appropriate logic to provide control. this is done using
the SL-79 command. The recloser logic settings are summarized in Table 4-31. Additionally, one or more
of the protection elements must be connected to external elements that are controlled by the SL-<func> or
SL-VO command.

Table 4-31. Recloser Logic Settings

Function

Range/Purpose

Default

Mode

0 = Recloser disabled
1 = Standard power-up operation. After power-up, the STATUS logic must

be TRUE for the Reset time delay or the recloser automatically goes
to Lockout. If the STATUS logic stays TRUE for reset time delay, the
recloser goes to Reset.

2 = Power-up to close. If the recloser was in the Reset state when power

was lost, and when power is restored the STATUS logic is FALSE
(breaker open) and the RI logic is TRUE, the recloser will initiate the
first reclose operation. If the STATUS logic stays TRUE for the reset
time delay, the recloser goes to Reset.

0

RI

OR logic term to initiate the operation of the reclosing function

0

STATUS

OR logic term to indicate breaker status.
TRUE/1 = closed, FALSE/0 = open

0

WAIT

OR logic term to momentarily disable but not reset the recloser

0

LOCKOUT

OR logic term to disable the recloser (drive to Lockout)

0

SL-79 Command

Purpose:

Read or set 79 function block logic.

Syntax:

SL-79[=<Mode>,<RI>,<STATUS>,<WAIT>,<LOCKOUT>]

SL-79 Command Example
1.

Read the recloser logic settings.
>SL-79

1,VO1,/IN2,0,IN3

The reported settings are explained in the following paragraphs.

1

Recloser is enabled for standard, power-up operation.

VO1

Recloser is initiated when output VO1 is TRUE.

/IN2

Breaker status is monitored at contact input 2. (Breaker is closed when IN2 is de-energized.)

0

Reclose Wait is disabled.

IN3

Energizing contact input 3 will block reclosing and drive the recloser to Lockout.

Courtesy of NationalSwitchgear.com

«
...
90
91
92
93
94
...
»

Содержание BE1-951









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-951

Бренд: K&K Страницы: 9

Бренд: Mustang Survival Страницы: 32

Бренд: Quasar Страницы: 58

Бренд: GE Страницы: 436

Бренд: Panasonic Страницы: 18

Бренд: Jula Страницы: 10

Бренд: Hitachi Страницы: 68

Бренд: Hitachi Страницы: 67

Бренд: Hitachi Страницы: 164

Бренд: Hitachi Страницы: 64

Бренд: NEO TOOLS Страницы: 10

Бренд: Safety Technology International Страницы: 2

Enardo DFA Series

Бренд: Emerson Страницы: 12

Бренд: Vestil Страницы: 3

Бренд: Covalliero Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды