Basler BE1-951 Скачать руководство пользователя страница 298 | Manualshive

Страница: 298 / 424

background image

12-30

Installation

BE1-951

SETTINGS

Settings for your application need to be entered and confirmed before placing the relay in service. Register
settings such as breaker operations and breaker duty can be entered to match the current state of your
system.

PREPARING THE RELAY FOR SERVICE

Basler microprocessor-based protection systems are similar in nature to a panel of electromechanical or
solid-state component relays. Both must be wired together with inputs and outputs, and have operating
settings applied. Logic settings determine which protection elements are electronically wired to the inputs
and outputs of the device. Operating settings determine the pickup thresholds and time delays.

The logic and operating settings should be tested by applying actual inputs and operating quantities and
verifying proper output response. For more details, refer to Section 14,

Testing and Maintenance. All of the

following connections and functions should be verified during commissioning tests.

•

Proper connection and sensing of current and voltage signals

•

Input and output contact connections

•

I/O sensing versus virtual sensing

•

Settings validation

•

Proper operation of equipment (main or auxiliary)

•

Proper alarming (to SCADA) and/or targeting

Refer to Section 7,

BESTlogic Programmable Logic for information about customizing preprogrammed logic

and creating user-defined logic, and Section 8,

Application for information about the application of

preprogrammed logic schemes.

COMMUNICATIONS CONNECTIONS

The following paragraphs describe the communication connections for the BE1-951. Section 11,

ASCII

Command Interface provides information about using the relay communication interface and lists all
communication commands along with a description and the syntax for each command.

RS-232 Connectors
Front and rear panel RS-232 connectors are Data Communication Equipment (DCE) DB-9 female
connectors. Connector pin numbers, functions, names and signal directions are shown in Table 12-1.
RS-232 cable connection diagrams are provided in Figures 12-33 through 12-35. Optional Clear to Send
(CTS) and Request to Send (RTS) connections are required only if hardware handshaking is enabled.

Table 12-1. RS-232 Pinouts (COM0 and COM1)

Pin

Function

Name

Direction

1

Shield

----

N/A

2

Transmit Data

TXD

From Relay

3

Receive Data

RXD

Into Relay

4

N/C

----

N/A

5

Signal Ground

GND

N/A

6

N/C

----

N/A

7

N/C

----

N/A

8

N/C

----

N/A

9

N/C

----

N/A

Courtesy of NationalSwitchgear.com

«
...
296
297
298
299
300
...
»

Содержание BE1-951









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-951

Бренд: Eaton Страницы: 8

Бренд: I-Gard Страницы: 16

Бренд: ABB Страницы: 15

GUIDE PLUS+ Gold

Бренд: RCA Страницы: 64

Бренд: OBO Bettermann Страницы: 68

REL 551 2.3 Series

Бренд: ABB Страницы: 140

PT52LCX66 - MULTI MEDIA DISPLAY

Бренд: Panasonic Страницы: 83

Бренд: Samsung Страницы: 96

RU-44SZ80L - - 44" Rear Projection TV

Бренд: LG Страницы: 43

Бренд: hecht Страницы: 4

ACP Hardwire Series

Бренд: Transtector Страницы: 2

SANDOR DUAL SMA

Бренд: Politec Страницы: 24

Бренд: Leviat Страницы: 16

Бренд: Liski Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды