Basler BE1-951 Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 424

background image

6-4

Reporting and Alarm Functions

BE1-951

CO-43/143/243/343

Virtual switch function status is reported on this line. This information is also available at HMI screen 1.5.4.
See Section 4,

Protection and Control for more information about virtual switch operation.

CO-101 (101SC)

This line reports the current status of the virtual breaker control switch slip contact output. More information
about the virtual breaker control switch is available in Section 4,

Protection and Control.

CO-Group

The logic override status of the setting group selection function is reported on this line. For more information
about this function, refer to Section 4,

Protection and Control, Setting Groups.

Active Logic

This line reports the name of the active logic scheme. The active logic scheme name can also be viewed
at HMI screen 5 and through the SL-N command. See Section 7, BESTlogic Programmable Logic, Logic
Scheme Names for more information about this function.

Recloser (79)

The status of the recloser is reported on this line. HMI screen 1.1 also reports this information. More
information about the recloser function is available in Section 4,

Protection and Control.

Logic Var (00-31), Logic Var (32-63), and Logic Var (64-95)

These three lines report the status of each BESTlogic variable. These lines can be entered into Table 6-3
to determine the status of each logic variable. Section 7,

BESTlogic Programmable Logic provides more

information about BESTlogic variables.

Active Group

The active setting group is indicated on this line. HMI screen 1.5.5 also provides this information. See
Section 4,

Protection and Control for more information about setting groups.

Breaker (52)

This line reports the state of the breaker. This information is also available at HMI screen 1.5.6. More
information about breaker status is provided in the Breaker Monitoring subsection.

Diag/Alarm

This line reports the status of the Relay Trouble Alarm, Major Alarm, Minor Alarm, and Logic Alarm. The
status of these alarms can be viewed at HMI screen 1.3. Front panel LEDs also indicate the status of the
Relay Trouble Alarm, Minor Alarm, and Major Alarm. Alarm status is also available through the
communication ports. The SA-MIN command repors the Minor Alarm status, the SA-MAJ command reports
the Major Alarm status, and the SA-LGC command reports the Logic Alarm status.

Courtesy of NationalSwitchgear.com

«
...
122
123
124
125
126
...
»

Содержание BE1-951









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-951

Бренд: SIP Protection Страницы: 4

DRP Version 2.0-BLUE

Бренд: ZDS Страницы: 20

Бренд: ABB Страницы: 188

Бренд: ABB Страницы: 66

Бренд: ABB Страницы: 12

Бренд: ABB Страницы: 24

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 68

Бренд: ABB Страницы: 4

Бренд: NEC Страницы: 34

Бренд: NEC Страницы: 32

EVO-ALL AUDI Q3

Бренд: Fortin Страницы: 6

Бренд: LG Страницы: 29

Бренд: Vollrath Страницы: 2

Бренд: ABB Страницы: 98

DRYSUIT Neoprene

Бренд: Uwatec Страницы: 172

Jetstream Series

Бренд: TP-Link Страницы: 2

Бренд: Selcom Security Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды