manualshive.com logo in svg

Basler BE1-951, Инструкция по эксплуатации

Инструкция по эксплуатации для Basler BE1-951 - бесплатное руководство для пользователей, которое можно скачать с нашего сайта. Этот мануал поможет вам настроить и использовать ваш продукт наилучшим образом. Не теряйте время, загрузите его прямо сейчас и начните с эксплуатацией Basler BE1-951.

Поделиться
Скачать
background image

BE1-951

Security

9-1

SECTION 9 • SECURITY

INTRODUCTION

Security, in the form of multilevel password protection, is discussed along with the information required for
protecting specific function groups and user interface components against unauthorized access.

Passwords provide access security for three distinct functional access areas: Settings, Reports, and Control.
Each functional area can be assigned a unique password or one password can be assigned to multiple
areas. A global password is used to access all three of the functional areas. BE1-951 passwords are not
case sensitive; either lowercase or uppercase letters may be entered. Password security only limits write
operations; passwords are never required to read information from any area.

Additional security is provided by controlling the functional areas that can be accessed from a particular
communication port.  For example, security can be configured so that access to Control commands from the
rear RS-232 port (COM1) is denied.  Then, an attempt to issue a Control command through COM1 will cause
the relay to respond with an ACCESS DENIED and/or INVALID PASSWORD message.  This will occur
whether a valid password is entered or not.  When configuring communication port access areas, you should
be aware that the front RS-232 port (COM0) and the front panel HMI are treated as the same port.

The communication ports and password parameters act as a two-dimension control to limit changes.  For
a command to be accepted, the entered password must be correct and the command must be entered
through a valid port.  Only one password can be active at one time for any area or port.  For example, if a
user gains write access at COM1, then users at other areas (COM0, front panel HMI, and COM2) won’t be
able to gain write access until the user at COM1 uses the EXIT command to release access control.

If a port holding access privileges, sees no activity (command entered or HMI key pressed) for approximately
five minutes, access privileges and any pending changes will be lost.  This feature ensures that password
protection can’t be accidentally left in a state where access privileges are enabled for one area and other
areas locked out for an indefinite period.

If password protection is disabled, then entering ACCESS= followed by no password or any alphanumeric
character string will obtain access to the unprotected area(s).

Setting Up Password Protection

Password protection is configured for each access area port and communication port with the GS-PW
(Global Security-PassWord) command. Password protection settings are summarized in Table 1-1.  

If the relay is ordered with an advanced protocol, security parameters accessed by COM2 may not apply.
See the appropriate protocol manual for details.  

Table 9-1. Password Protection Settings

Setting

Range/Purpose

password

User defined alphanumeric string with a maximum of 8 characters
A setting of 0 disables password protection.

com

ports

0 = Front RS-232 port
1 = Rear RS-232 port
2 = Rear RS-485 port

Multiple ports may be selected by using
a slash (/) between each port
designator.

Courtesy of NationalSwitchgear.com

Содержание BE1-951









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-951

LEADING EDGE SAFETY R2000 Instruction Manual preview
R2000
Бренд: LEADING EDGE SAFETY Страницы: 36
Magnavox 55P8288 Directions For Use Manual preview
55P8288
Бренд: Magnavox Страницы: 54
Muirhead 3565 Product Manual preview
3565
Бренд: Muirhead Страницы: 28
Haas Way Cover Troubleshooting Manual preview
Way Cover
Бренд: Haas Страницы: 7
Markilux planet flex Operation Manual preview
planet flex
Бренд: Markilux Страницы: 3
Noark PMF 12 Mounting Instruction preview
PMF 12
Бренд: Noark Страницы: 4
Palmer Safety C0850 User Instructions preview
C0850
Бренд: Palmer Safety Страницы: 4
ABB RED650 Technical Manual preview
RED650
Бренд: ABB Страницы: 926
Samsung HLT6156WX Owner'S Instructions Manual preview
HLT6156WX
Бренд: Samsung Страницы: 144
ABB REL650 series Technical Manual preview
REL650 series
Бренд: ABB Страницы: 856
GE MLP1000 Manual preview
MLP1000
Бренд: GE Страницы: 141
RST Power T1+T2 1+0 275V (FM) Installation Manual preview
Power T1+T2 1+0 275V (FM)
Бренд: RST Страницы: 2
U-Line Leighting L3 Instructions preview
Leighting L3
Бренд: U-Line Страницы: 3
System Sensor MASS12/24ADA Series Installation And Maintenance Instructions Manual preview
MASS12/24ADA Series
Бренд: System Sensor Страницы: 36
hecht KM1504002 Instructions For Use preview
KM1504002
Бренд: hecht Страницы: 4
Toshiba 42H83 Owner'S Manual preview
42H83
Бренд: Toshiba Страницы: 59
Toshiba 46WM48P Service Manual preview
46WM48P
Бренд: Toshiba Страницы: 97
LG DU-52SZ61D Service Manual preview
DU-52SZ61D
Бренд: LG Страницы: 55

Бренды по названию

Популярные бренды

Загрузить еще бренды