manualshive.com logo in svg

Basler BE1-951, Инструкция по эксплуатации

Инструкция по эксплуатации для Basler BE1-951 - бесплатное руководство для пользователей, которое можно скачать с нашего сайта. Этот мануал поможет вам настроить и использовать ваш продукт наилучшим образом. Не теряйте время, загрузите его прямо сейчас и начните с эксплуатацией Basler BE1-951.

Поделиться
Скачать
background image

4-30

Protection and Control

BE1-951

Figure 4-16.  Under/Overvoltage Element

Time delay settings entered in cycles are converted to seconds or milliseconds (per the nominal frequency
setting stored in EEPROM) before being stored. See Section 3, 

Input and Output Functions, Voltage

Measurement Functions for more information about this setting. If the nominal frequency setting is being
changed from the default (60 hertz) and time delay settings are being set in cycles, the frequency setting
should be entered and saved before making any time delay settings changes.

27X/59X/159X Auxiliary Under/Over Voltage Protection

Figure 4-16 illustrates the inputs and outputs of the auxiliary under/overvoltage elements. Element operation
is described in the following paragraphs.

The auxiliary elements have two outputs: 27X/59X/159XPU (pickup) and 27X/59X/159XT (trip). When the
monitored voltage increases above the pickup setting, the pickup output becomes TRUE and the element
starts timing toward a trip. The trip output becomes TRUE when the element timer times out.

The Block (BLK) input is used to disable protection. A BESTlogic expression defines how the BLK input
functions. When this expression is TRUE, the element is disabled by forcing the outputs to logic 0 and
resetting the timer. This feature functions in a similar way to the torque control contact of an
electromechanical relay.

The 27X, 59X, and the 159X elements are enabled or disabled by the Mode input. Four modes are available.
Selecting Mode 0 disables protection. Mode 1, 2, or 3 enables the element, as described in this section
under 

BESTlogic Settings for the Auxiliary Under/Overvoltage Element.

The pickup setting determines the voltage pickup level of the element. The time delay setting controls how
long it takes for the trip output to become TRUE after the pickup output becomes TRUE. When the monitored
voltage increases above the pickup threshold, the pickup output becomes TRUE and the timer starts. If the
voltage remains above the pickup threshold for the duration of the time delay setting, the trip output becomes
TRUE. If the voltage decreases below the 59X/159X dropout ratio of 98 percent, or increases above the 27X
dropout ratio of 100%, the timer is reset to zero.  

If the 60FL element trip logic is true, and V block is enabled for 3VO blocking (N), the 27X/59X/159X
functions will be blocked if they are set to mode 2.  For more information on the 60FL function, see the
paragraphs later in this section.

If the target is enabled for the 59X/159X element, the target reporting function will record a target when the
trip output is TRUE and the fault recording function trip logic expression is TRUE. See Section 6, 

Reporting

and Alarm Functions, Fault Reporting Functions for more information about target reporting.The overcurrent
elements have adaptable targets.  If one is set for directional control, it will report a 67 target.  If one is set
for non-directional control it will report a 59 target.

BESTlogic Settings for the auxiliary Under/Overvoltage Elements

Logic settings for the 27X/59X/159X function are made using the SL-27X (settings logic–undervoltage)
command or the SL-59X and SL159X (settings logic–overvoltage) command. The settings of these
commands determine whether the elements are enabled or disabled. The SL command also provides

Courtesy of NationalSwitchgear.com

Содержание BE1-951









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-951

Worker 11876 User Manual preview
11876
Бренд: Worker Страницы: 7
I-Gard IPC DSP OHMNI Instruction Manual preview
IPC DSP OHMNI
Бренд: I-Gard Страницы: 40
Cambium Networks PTP 650 LPU Installation Manual preview
PTP 650 LPU
Бренд: Cambium Networks Страницы: 16
STI UM Series Manual preview
UM Series
Бренд: STI Страницы: 18
K40 RL200i Owner'S Manual preview
RL200i
Бренд: K40 Страницы: 20
Home Protector 64153 User Manual preview
64153
Бренд: Home Protector Страницы: 24
Kanlux 04-0031 Manual preview
04-0031
Бренд: Kanlux Страницы: 2
Panasonic PT51G36E - 51" PROJECTION TV Service Manual preview
PT51G36E - 51" PROJECTION TV
Бренд: Panasonic Страницы: 27
Arcteq AQ-102LV Manual preview
AQ-102LV
Бренд: Arcteq Страницы: 37
Amina APU-RS8E Installation Manual preview
APU-RS8E
Бренд: Amina Страницы: 7
Samsung HCN436W Owner'S Instructions Manual preview
HCN436W
Бренд: Samsung Страницы: 71
Panasonic PT 52LCX66 Operating Instructions Manual preview
PT 52LCX66
Бренд: Panasonic Страницы: 80
Raycap ProSMS 8 Installation Manual preview
ProSMS 8
Бренд: Raycap Страницы: 24
Philips 46PP9501 User Manual preview
46PP9501
Бренд: Philips Страницы: 34
Philips 46PP9302H Quick Use And Setup Manual preview
46PP9302H
Бренд: Philips Страницы: 8
Philips 46PW9527 Directions For Use Manual preview
46PW9527
Бренд: Philips Страницы: 36
Philips 46PP9352 Quick Use And Setup Manual preview
46PP9352
Бренд: Philips Страницы: 8
Philips 48PP9103 Operating Manual preview
48PP9103
Бренд: Philips Страницы: 100

Бренды по названию

Популярные бренды

Загрузить еще бренды