manualshive.com logo in svg

Agilent Technologies 1290 Infinity II 2D-LC Solution, Руководство пользователя

Поделиться
Скачать
Agilent Technologies 1290 Infinity II 2D-LC Solution Скачать руководство пользователя страница 384

15

Appendix

General Safety Information

2D-LC User Guide

384

Before Applying Power

Ground the Instrument

WARNING

Wrong voltage range, frequency or cabling
Personal injury or damage to the instrument

Verify that the voltage range and frequency of your power distribution 
matches to the power specification of the individual instrument.

Never use cables other than the ones supplied by Agilent Technologies 
to ensure proper functionality and compliance with safety or EMC 
regulations.

Make all connections to the unit before applying power.

NOTE

Note the instrument's external markings described under 

“Safety Symbols”

on 

page 387.

WARNING

Missing electrical ground
Electrical shock

If your product is provided with a grounding type power plug, the 
instrument chassis and cover must be connected to an electrical ground 
to minimize shock hazard.

The ground pin must be firmly connected to an electrical ground (safety 
ground) terminal at the power outlet. Any interruption of the protective 
(grounding) conductor or disconnection of the protective earth terminal 
will cause a potential shock hazard that could result in personal injury.

Содержание 1290 Infinity II 2D-LC Solution












































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды