manualshive.com logo in svg

Agilent Technologies 1290 Infinity II 2D-LC Solution, Руководство пользователя

Поделиться
Скачать
Agilent Technologies 1290 Infinity II 2D-LC Solution Скачать руководство пользователя страница 383

2D-LC User Guide

383

15

Appendix

General Safety Information

General Safety Information

General Safety Information

The following general safety precautions must be observed during all phases of 
operation, service, and repair of this instrument. Failure to comply with these 
precautions or with specific warnings elsewhere in this manual violates safety 
standards of design, manufacture, and intended use of the instrument. Agilent 
Technologies assumes no liability for the customer’s failure to comply with these 
requirements.

Safety Standards

This is a Safety Class I instrument (provided with terminal for protective earthing) 
and has been manufactured and tested according to international safety 
standards. 

General

Do not use this product in any manner not specified by the manufacturer. The 
protective features of this product may be impaired if it is used in a manner not 
specified in the operation instructions.

WARNING

Ensure the proper usage of the equipment.
The protection provided by the equipment may be impaired.

The operator of this instrument is advised to use the equipment in a 
manner as specified in this manual.

Содержание 1290 Infinity II 2D-LC Solution












































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды