manualshive.com logo in svg

Yamaha XTZ750, User Manual

The Yamaha XTZ750 User Manual is essential for any owner or enthusiast of this powerful off-road motorcycle. Our website offers a free download of the manual, providing detailed instructions, maintenance tips, and troubleshooting advice. Get your copy now from manualshive.com and make the most out of your XTZ750 experience.

Share
Download
background image

UNREGISTERED VI

 

Identification numbers

 

09

 

 

Frame and engine numbers 

The  frame  serial  number  is  stamped  into  the 

right  side  of  the  steering  head.  The  engine 
number is stamped into the top of the crankcase 
on  the  right-hand  side  of  the  engine.  Both  of 
these numbers should be recorded and kept in a 
safe  place  so  they  can  be  furnished  to  law 
enforcement officials in the event of a theft. There 
is also  a  carburettor  identification  number  on  the 
intake side of each carburettor body, and a colour 
code label on the top of the rear fender under the 
passenger  seat.  The  colour  code label  may  also 
contain  the  bike's  production  year  and  model 
code.

 

The  frame  serial  number,  engine  serial 

number,  carburettor  identification  number  and 
colour code should also be kept in a handy place 
(such  as  with  your  driver's  licence)  so  they  are 
always  available  when  purchasing  or  ordering 
parts for your machine.

 

The  procedures  in  this  manual  identify  the 

bikes  by  model  type  (eg  TDM)  and  if  necessary 
by production year. Note that the production year 
does not necessarily correspond with the year of 
sale or registration.

 

The  model  code  number  is  very  useful  when 

ordering  parts  for  your  bike  and  is  linked  to  the 
production  year  as  shown  in  the  accompanying 
table. There should be a sticker on the bike's rear 
frame  section  (usually  visible  once  the  seat  is 
lifted)  which  gives  the  model  code  number  (eg 
4TX4,  meaning  a  1999  TDM),  the  Yamaha 
production  code  number,  and  a  letter  indicating 
the  colour  code. The  frame  and  engine  numbers 
can also be used to establish the production year 
and model code, although these are not available 
for  post-1995  models.  The  accompanying  table 
gives  model  identification  data  for  models 
available in the UK market.

 

Buying spare parts 

Once  you  have  found  all  the  identification 

numbers, record them for reference when buying 
parts. 

Since 

the 

manufacturers 

change 

specifications, parts and vendors (companies that 
manufacture 

various 

components 

on 

the 

machine),  providing  the  ID  numbers  is  the  only 
way  to  be  reasonably  sure  that  you  are  buying 
the correct parts.

 

Whenever  possible,  take  the  worn  part  to  the 

dealer  so  direct  comparison  with  the  new 
component can be made. Along the trail from the 
manufacturer  to  the  parts  shelf,  there  are 
numerous  places  that  the  part  can  end  up  with 
the wrong number or be listed incorrectly.

 

The two places to purchase new parts for your 

motorcycle  -  the  accessory  store  and  the 
franchised dealer - differ in the type of parts they 
carry.  While  dealers  can  obtain  virtually  every 
part  for  your  motorcycle,  the  accessory  dealer is 
usually limited to normal high wear items such as 
shock  absorbers,  tune-up  parts,  various  engine 
gaskets, cables, chains,

 

 

Model type

 

ProdYr

 

Model code

 

Frame No.

 

Engine No.

 

TDM850

 

1991

 

3VD1

 

000101 on

 

000101 on

 

 

1992

 

3VD4

 

022101 on

 

022101 on

 

 

1993

 

3VD5

 

040101 on

 

040101 on

 

 

1994

 

3VD7

 

060101 on

 

060101 on

 

 

1995

 

3VD9

 

079101 on

 

079101 on

 

 

1996

 

4TX1

 

not available

 

 

 

1997

 

4TX2

 

not available

 

 

 

1998

 

4TX3

 

not available

 

 

 

1999

 

4TX4

 

not available

 

 

TRX850

 

1996

 

4UN1

 

000101 on

 

000101 on

 

 

1997

 

4UN3

 

not available

 

 

 

1998/9

 

4UN4

 

not available

 

 

XTZ750

 

1989

 

3LD1

 

000101 on

 

000101 on

 

 

1990

 

3UD3

 

032101 on

 

032101 on

 

 

1991

 

3LD4

 

048101 on

 

048101 on

 

 

1992

 

3LD5

 

063101 on

 

063101 on

 

 

1993

 

3LD6

 

079101 on

 

079101 on

 

 

1994

 

3LD7

 

092101 on

 

092101 on

 

 

1995

 

3LD8

 

100101 

on

 

100101 

on

 

 

 

The frame number is stamped on the right-

hand side of the steering head

 

The engine number is stamped into the top

 

of the crankcase on the right-hand side of

 

the engine.

 

brake parts, etc. Rarely will an accessory outlet have 
major 

suspension 

components, 

cylinders, 

transmission gears, or cases.

 

Used  parts  can  be  obtained  for  roughly  half  the 

price  of  new  ones,  but  you  can't  always  be  sure  of 
what you're getting. Once again, take

 

Summary of Contents for XTZ750




















































































































































































































Reviews:

No comments

Related manuals for XTZ750

LAZER CORSICA User Manual preview
CORSICA
Brand: LAZER Pages: 19
Yukon Trail Puma 200 Owner'S Manual preview
Puma 200
Brand: Yukon Trail Pages: 21
R&G CP0473 Fitting Instructions Manual preview
CP0473
Brand: R&G Pages: 14
MOSKO MOTO Scout 25L Pannier Kit V2.0 Installation Instructions Manual preview
Scout 25L Pannier Kit V2.0
Brand: MOSKO MOTO Pages: 13
Takegawa TwinSpark Super head plus R Instruction Manual preview
TwinSpark Super head plus R
Brand: Takegawa Pages: 5
BMW K 1200RS Repair Manual preview
K 1200RS
Brand: BMW Pages: 416
KC N901 User Manual preview
N901
Brand: KC Pages: 32
MT Helmets KRE+ Instructions Manual preview
KRE+
Brand: MT Helmets Pages: 116
APRILIA RS4 125 Service Manual preview
RS4 125
Brand: APRILIA Pages: 155
APRILIA PEGASO 650 STRADA Service Station Manual preview
PEGASO 650 STRADA
Brand: APRILIA Pages: 236
Honda CRF150F 2007 Owner'S Manual preview
CRF150F 2007
Brand: Honda Pages: 191
Polaris 600 Dragon SP Owner'S Manual preview
600 Dragon SP
Brand: Polaris Pages: 153
Honda Monkey 2021 Manual preview
Monkey 2021
Brand: Honda Pages: 106
Honda Goldwing GL1100 Interstate 1981 Owner'S Manual preview
Goldwing GL1100 Interstate 1981
Brand: Honda Pages: 100
Honda Grom125 2015 Manual preview
Grom125 2015
Brand: Honda Pages: 118
Honda Degree XL250 Owner'S Manual preview
Degree XL250
Brand: Honda Pages: 108
Honda GL1800A Owner'S Manual preview
GL1800A
Brand: Honda Pages: 194
Honda GL 1200 A '84 Aspencade Parts Manual preview
GL 1200 A '84 Aspencade
Brand: Honda Pages: 280

Brands by name

Popular brands

Load more brands