Yamaha XTZ750 User Manual Download | Manualshive

Page: 113 / 211

background image

Fuel and exhaust systems 4»7

6 Carburettor overhaul -

general information

1

Poor engine performance, hesitation, hard

starting, stalling, flooding and backfiring are all
signs that major carburettor maintenance may be
required.

2  Keep  in  mind  that  many  so-called  carburettor
problems  are  really  not  carburettor  problems  at
all, but mechanical problems within the engine or
ignition  system  malfunctions.  Try  to  establish  for
certain  that  the  carburettors  are  in  need  of
maintenance before beginning a major overhaul.
3  Check  the  fuel  tap  and  filter,  the  fuel  and
vacuum  hoses,  the  intake  manifold  joint  clamps,
the air filter, the ignition system, the spark plugs,
valve clearances and carburettor synchronisation
before  assuming  that  a  carburettor  overhaul  is
required.
4  Most  carburettor  problems  are  caused  by  dirt
particles,  varnish  and  other  deposits  which  build
up  in  and  block  the  fuel  and  air  passages,
especially if the motorcycle has been laid up for a
time. Also, in time, gaskets and O-rings shrink or
deteriorate  and  cause  fuel  and  air  leaks  which
lead to poor performance.
5  When

overhauling

the

carburettors,

disassemble them completely and clean the parts
thoroughly with a carburettor cleaning solvent
and

dry

them

with

filtered,

unlubricated

compressed  air.  Blow  through  the  fuel  and  air
passages  with  compressed  air  to  force  out  any
dirt  that  may  have  been  loosened  but  not
removed  by  the  solvent.  Once  the  cleaning
process  is  complete,  reassemble  the  carburettor
using new gaskets and O-rings.
6  Before  disassembling  the  carburettors,  make
sure  you  have  all  necessary  O-rings  and  other
parts, some carburettor cleaner, a supply of clean
rags, some means of blowing out the carburettor
passages  and  a  clean  place  to  work.  It  is
recommended  that  only  one  carburettor  be
overhauled at a time to avoid mixing up parts.

7.4a Idle speed adjuster bolt (arrowed) -TDM

models

7 Carburettors

-

^

removal and installation

«|

Warning: Refer to the precautions
given in Section 1 before starting
work.

Removal

1

Remove the fuel tank and the air filter housing

(see Sections 2 and 4).

2  Slacken  the  choke  outer  cable  bracket  screw
and free the cable from the bracket on the front of
the  carburettors,  then  detach  the  inner  cable
nipple  from  the  choke  linkage  lever

(see

illustrations).

3

Detach

the

throttle

cables

from

the

carburettors (see Section 11, Steps 2 and 3).

7.4b Idle speed adjuster bolt (arrowed)

-

TRX

models

If access is too restricted, detach them after the
carburettors have been lifted off the cylinder
head intakes.

4  On  TDM  and  TRX  models,  unscrew  the  bolt
securing  the  idle  speed  adjuster  and  feed  it
through  to  the  base  of  the  carburettors

(see

illustrations).

5

Release the clamp securing the drain hose to

the bottom of each float chamber and detach the
hoses

(see illustration).

Also release the clamp

securing the fuel supply hose to the carburettors
and detach the hose

(see illustration);

be

careful to catch the small gauze filter fitted in the
fuel supply hose union as the hose is detached
(except 1999 TDM models).

6 On 1996-on TDM models and TRX models,
disconnect the wiring connector from the throttle
position sensor on the left-hand end of the
carburettors

(see illustration).

Also

7.5a Detach the drain hoses (arrowed)...

7.5b

...

and the fuel hose

7.6 Disconnect the throttle position sensor

wiring connector (arrowed)

Staned by Stalker

7.2b ... and detach the cable end from the

lever

7.2a Slacken the clamp screw (arrowed)...

A

«
...
111
112
113
114
115
...
»

Summary of Contents for XTZ750




















































































































































































































Reviews:

No comments

Related manuals for XTZ750

Brand: R&G Pages: 24

Brand: hepco & becker Pages: 4

Brand: R&G Pages: 9

Brand: Suzuki Pages: 526

Daytona 955i 2002

Brand: Triumph Pages: 384

Brand: hepco & becker Pages: 5

Brand: yasuni Pages: 9

Brand: BMW Pages: 19

Brand: hepco & becker Pages: 2

Brand: R&G Pages: 17

Brand: R&G Pages: 18

Brand: R&G Pages: 17

Brand: Vanucci Pages: 35

Brand: Yamaha Pages: 9

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 91

Brand: Yamaha Pages: 92

Virago XV250 2004

Brand: Yamaha Pages: 95

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands