Xilinx LogiCORE IP Product Manual Download Page 71

Page: 71 / 142

XAUI v12.3 Product Guide

www.xilinx.com

PG053 April 6, 2016

Chapter 3:

Designing with the Core

Keep It Registered

To simplify timing and increase system performance in an FPGA design, keep all inputs and

outputs registered between your application and the core. This means that all inputs and

outputs from your application should come from, or connect to a flip-flop. While

registering signals might not be possible for all paths, it simplifies timing analysis and

makes it easier for the Xilinx

tools to place and route the design.

Recognize Timing Critical Signals

The supplied constraint file provided with the example design for the core identifies the

critical signals and the timing constraints that should be applied. See

Chapter 8,

Constraining the Core

for further information.

Use Supported Design Flows

The core HDL is added to the open Vivado® Design Suite project. Later the core is

synthesized along with the rest of the project as part of project synthesis.

Make Only Allowed Modifications

The XAUI core is not user-modifiable. Do not make modifications as they might have

adverse effects on system timing and protocol compliance. Supported user configurations

of the XAUI core can only be made by selecting the options from within the Vivado Design

Suite when the core is generated. See

Chapter 7, Customizing and Generating the Core

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands

Xilinx LogiCORE IP, Product Manual

Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands