Xilinx LogiCORE IP Product Manual Download Page 20

Page: 20 / 142

XAUI v12.3 Product Guide

www.xilinx.com

PG053 April 6, 2016

Chapter 2:

Product Specification

gt0_rxnotintable_out[3:0]

out

clk156_out

Active-High indicates the corresponding byte of the

received data was not a valid character in the 8B/10B

table.

gt0_rxcommadet_out

out

clk156_out This signal is asserted when the comma alignment

block detects a comma.

CHANNEL 1

GT1 DRP

gt1_drpaddr[8:0]

dclk

DRP address bus for channel 1.

gt1_drpen

dclk

DRP enable signal.
0: No read or write operation performed.
1: enables a read or write operation.

gt1_drpdi[15:0]

dclk

Data bus for writing configuration data to the

transceiver for channel 1.

gt1_drpdo[15:0]

out

dclk

Data bus for reading configuration data from the

transceiver for channel 1.

gt1_drprdy

out

dclk

Indicates operation is complete for write operations

and data is valid for read operations for channel 1.

gt1_drpwe

dclk

DRP write enable for channel 1.
0: Read operation when drpen is 1.
1: Write operation when drpen is 1.

gt1_drp_busy

out

dclk

(GTPE2 all configurations or GTHE2 10G

configuration). Indicates the DRP interface is being

used internally by the serial transceiver and should not

be driven until this signal is deasserted.

GT1 TX Reset and Initialization

gt1_txpmareset_in

Async

Starts the TX PMA reset process.

gt1_txpcsreset_in

Async

Starts the TX PCS reset process.

gt1_txresetdone_out

out

clk156_out When asserted the serial transceiver TX has finished

reset and is ready for use.

GT1 RX Reset and Initialization

gt1_rxpmareset_in

Async

Starts the RX PMA reset process.

gt1_rxpcsreset_in

Async

Starts the RX PCS reset process.

gt1_rxpmaresetdone_out

out

Async

(GTHE2 and GTPE2) This active-High signal indicates

RX PMA reset is complete.

gt1_rxresetdone_out

out

clk156_out When asserted the serial transceiver RX has finished

reset and is ready for use.

GT1 Clocking

gt1_rxbufstatus_out[2:0]

out

clk156_out RX buffer status.

gt1_txphaligndone_out

out

Async

TX phase alignment done.

Table 2

‐

Transceiver Control and Status Ports —7 Series FPGAs

(Cont’d)

Signal Name

Direction

Clock
Domain

Description

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands

Xilinx LogiCORE IP, Product Manual

Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands