Xilinx LogiCORE IP Product Manual Download Page 116

Page: 116 / 142

XAUI v12.3 Product Guide

www.xilinx.com

116

PG053 April 6, 2016

Chapter 8:

Detailed Example Design

The example design contains the following:

• Clock management logic and clock buffer instances
• Re-timing registers on the parallel data interface, both on inputs and outputs
• An instance of the block level module which contains the core, transceiver wrappers

and associated logic

The example design allows the HDL to go through implementation and simulation. It is not

intended to be placed directly on a board and does not constrain the I/O pins.

The example design can be opened in a separate project by generating the

Examples

output product, then right clicking the core instance and choosing

Open IP Example

Design...

X-Ref Target - Figure 8-4

Figure 8

‐

Example HDL Wrapper for XAUI with Shared Logic in Core

(UltraScale Architecture)

component_name_gt (UltraScale wizard subcore)

XAUI Encrypted HDL

Clock Logic

component_name_clk_clocking.vhd/v

Reset Logic

component_name_clk_resets.vhd/v

Reg

Out

Support Clocking

component_name_support_clocking.vhd/v

component_name.vhd/v

component_name_example_design.vhd/v

UltraScale Architecture

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands

Xilinx LogiCORE IP, Product Manual

Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands