manualshive.com logo in svg

Xilinx LogiCORE IP, Product Manual

Share
Download
Xilinx LogiCORE IP Product Manual Download Page 96

XAUI v12.3 Product Guide

www.xilinx.com

96

PG053 April 6, 2016

Chapter 6:

Design Considerations

Clocking: Zynq-7000, Virtex-7, Artix-7, and Kintex-7 
Devices 

The clocking schemes in this section are illustrative only and might require customization 

for a specific application. 

Transceiver DRPCLK

A dedicated core input clock, 

dclk

, is connected to the DRPCLK port of the transceivers in 

the core for all 7-Series and Zync-7000 devices. This clock frequency is flexible; the example 

design uses a 50 MHz clock. Choosing a different frequency can allow for the sharing of 

DRPCLK across all transceivers in a device.

The 

dclk

 clock, provided to the core, must be a free running clock since it is also used to 

clock the logic for transceiver reset/initialization circuitry. The 

dclk

 clock must not be 

derived from any transceiver output clocks.

Transceiver Reference Clock 

10G — XAUI

The transceivers require a reference clock of 156.25 MHz to operate at a line rate of 3.125 

Gb/s.

20G — XAUI

The transceivers require a reference clock of 312.5 MHz to operate at a line rate of 

6.25 Gb/s.

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands