Xilinx LogiCORE IP Product Manual Download Page 23

Page: 23 / 142

XAUI v12.3 Product Guide

www.xilinx.com

PG053 April 6, 2016

Chapter 2:

Product Specification

gt2_drpdo[15:0]

out

dclk

Data bus for reading configuration data from the

transceiver for channel 2.

gt2_drprdy

out

dclk

Indicates operation is complete for write operations

and data is valid for read operations for channel 2.

gt2_drpwe

dclk

DRP write enable for channel 2.
0: Read operation when drpen is 1.
1: Write operation when drpen is 1.

gt2_drp_busy

out

dclk

(GTPE2 all configurations or GTHE2 10G

configuration). Indicates the DRP interface is being

used internally by the serial transceiver and should not

be driven until this signal is deasserted.

GT2 TX Reset and Initialization

gt2_txpmareset_in

Async

Starts the TX PMA reset process.

gt2_txpcsreset_in

Async

Starts the TX PCS reset process.

gt2_txresetdone_out

out

clk156_out When asserted the serial transceiver TX has finished

reset and is ready for use.

GT2 RX Reset and Initialization

gt2_rxpmareset_in

Async

Starts the RX PMA reset process.

gt2_rxpcsreset_in

Async

Starts the RX PCS reset process.

gt2_rxpmaresetdone_out

out

Async

(GTHE2 and GTPE2) This active-High signal indicates

RX PMA reset is complete.

gt2_rxresetdone_out

out

clk156_out When asserted the serial transceiver RX has finished

reset and is ready for use.

GT2 Clocking

gt2_rxbufstatus_out[2:0]

out

clk156_out RX buffer status.

gt2_txphaligndone_out

out

Async

TX phase alignment done.

gt2_txphinitdone_out

out

Async

TX phase alignment initialization done.

gt2_txdlysresetdone_out

out

Async

TX delay alignment soft reset done.

gt2_cplllock_out

out

Async

(GTHE2) This active-High PLL frequency lock signal

indicates that the PLL frequency is within

predetermined tolerance.

Signal Integrity and Functionality

GT2 Eye Scan

gt2_eyescantrigger_in

clk156_out Causes a trigger event.

gt2_eyescanreset_in

Async

This port is driven High and then deasserted to start

the EYESCAN reset process.

gt2_eyescandataerror_out

out

Async

Asserts High for one rec_clk cycle when an (unmasked)

error occurs while in the COUNT or ARMED state.

Table 2

‐

Transceiver Control and Status Ports —7 Series FPGAs

(Cont’d)

Signal Name

Direction

Clock
Domain

Description

Send Feedback

Summary of Contents for LogiCORE IP















































































































































Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands

Xilinx LogiCORE IP, Product Manual

Search results

Summary of Contents for LogiCORE IP

Reviews:

Related manuals for LogiCORE IP

Brands by name

Popular brands